N54Tech.com - International Turbo Racing Discussion
(#1)
Old
Mikeroo88 Mikeroo88 is offline
New Member
 
Posts: 4
Join Date: May 2019
Car: Kia stinger 2.0T
Default JB4 installation stinger 2.0 - 05-10-2019, 09:33 AM

Does anyone have any videos or good pictures of the connection to the OBDII.. videos provided are on the GT and I don’t have wires on same spot seen in video and wire doesn’t reach far enough inside the vehicle from behind the E break to make connections to the OBDII from inside. Not mechanically inclined need help

Last edited by Mikeroo88; 05-10-2019 at 10:55 AM..
Reply With Quote
(#2)
Old
Mikeroo88 Mikeroo88 is offline
New Member
 
Posts: 4
Join Date: May 2019
Car: Kia stinger 2.0T
Default 05-10-2019, 09:38 AM

Also tried using purchased wire as an extension but connection still not showing readings on the app.
Reply With Quote
(#3)
Old
NLJ NLJ is offline
Junior Member
 
Posts: 36
Join Date: Apr 2019
Car: G70
Default 05-10-2019, 11:27 AM

There's a little crevice where the fender meet the hood. You see it when you have your driver door open, see if you can push the small square through. Otherwise you will have to push it through the grommet in the firewall.

Last edited by NLJ; 05-24-2019 at 06:02 PM..
Reply With Quote
(#4)
Old
Mikeroo88 Mikeroo88 is offline
New Member
 
Posts: 4
Join Date: May 2019
Car: Kia stinger 2.0T
Default 05-10-2019, 11:31 AM

I went through the grommet however the wire is not long enough to reach the white wire of the OBDII. The JB4 is on the passenger side to reach the O2 sensor. I tried buying wire and using it as an extension but still not getting any feed to my app
Reply With Quote
(#5)
Old
Terry @ BMS's Avatar
Terry @ BMS Terry @ BMS is online now
Tuner
 
Posts: 28,798
Join Date: Jan 2008
Default 05-24-2019, 05:28 PM

Sorry I missed this thread... Did you get it sorted? if not post photos so I can better spot what the issue is.


Burger Motorsports
Home of the Worlds fastest N20s, N54s, N55s, S55s, N63s, and S63s!

It is the sole responsibility of the purchaser and installer of any BMS part to employ the correct installation techniques required to ensure the proper operation of BMS parts, and BMS disclaims any and all liability for any part failure due to improper installation or use. It is the sole responsibility of the customer to verify that the use of their vehicle and items purchased comply with federal, state and local regulations. BMS claims no legal federal, state or local certification concerning pollution controlled motor vehicles or mandated emissions requirements. BMS products labeled for use only in competition racing vehicles may only be used on competition racing vehicles operated exclusively on a closed course in conjunction with a sanctioned racing event, in accordance with all federal and state laws, and may never be operated on public roads/highways. Please click here for more information on legal requirements related to use of BMS parts.
Reply With Quote
(#6)
Old
TStaino TStaino is offline
New Member
 
Posts: 9
Join Date: May 2019
Car: 2109 Kia Stinger 2.0T AWD
Default 05-31-2019, 06:03 AM

@Terry @ BMS do you have any pictures of exactly where the fuel wires go in the 2L Stinger?

I’m not the most mechanically inclined so telling me “it’s on the intake manifold” is like speaking Chinese to me...

A quick picture of which exact wires I am messing with would make me feel a lot better about puncturing holes in them.

Thanks again for an AMAZING product!
Reply With Quote
(#7)
Old
NLJ NLJ is offline
Junior Member
 
Posts: 36
Join Date: Apr 2019
Car: G70
Default 05-31-2019, 07:34 AM

Back of the engine towards the firewall from the passenger side:

N54Tech.com - International Turbo Racing Discussion - View Single Post - Kia Hyundai JB4
Reply With Quote
(#8)
Old
TStaino TStaino is offline
New Member
 
Posts: 9
Join Date: May 2019
Car: 2109 Kia Stinger 2.0T AWD
Default 05-31-2019, 04:59 PM

Thanks Terry. I see the first wire.. but not sure where the second one goes..

I watched the video you made of the 3.3 Stinger install, but the second wire goes not the driver side of the engine, and my driver side of the engine doesn't look like that... so I'm half way there, but still half way lost...

Please see attached.. the first picture is where the "short" wire goes, right? On the white wire?

But the "long" wire... ? Could it be the second picture?
Attached Images
  
Reply With Quote
(#9)
Old
TStaino TStaino is offline
New Member
 
Posts: 9
Join Date: May 2019
Car: 2109 Kia Stinger 2.0T AWD
Default 06-01-2019, 07:40 AM

Orrr am I only supposed to be using one wire because I only have one turbo?

When I said I wasn’t mechanically inclined, what I meant to say was..

n0o0o0o0o0o0o0o0o0b!
Reply With Quote
(#10)
Old
NLJ NLJ is offline
Junior Member
 
Posts: 36
Join Date: Apr 2019
Car: G70
Default 06-01-2019, 07:47 AM

Only long wire on the 2.0t.
Reply With Quote
(#11)
Old
TStaino TStaino is offline
New Member
 
Posts: 9
Join Date: May 2019
Car: 2109 Kia Stinger 2.0T AWD
Default 06-01-2019, 07:59 AM

Thank you! And that goes on the white wire in my first picture above?
Reply With Quote
(#12)
Old
NLJ NLJ is offline
Junior Member
 
Posts: 36
Join Date: Apr 2019
Car: G70
Default 06-01-2019, 08:48 AM

If that's the back of the engine on the passenger side towards the firewall, then yes. It connects to the #2 label on the harness plug.
There's an image of it a few pages back on the main page. Sometime in April.
Reply With Quote
(#13)
Old
TStaino TStaino is offline
New Member
 
Posts: 9
Join Date: May 2019
Car: 2109 Kia Stinger 2.0T AWD
Default 06-01-2019, 08:59 AM

It is! Thank you again!
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump




vBulletin Skin developed by: vBStyles.com
Copyright © 2007 - 2018, N54tech.com