N54Tech.com - International Turbo Racing Discussion
(#1)
Old
dmikhael619 dmikhael619 is offline
New Member
 
Posts: 10
Join Date: Aug 2016
Car: 2008 e92 335i
Default 335I Crank But no Start, DME Failure? - 11-05-2019, 09:32 AM

Could use a bit of help. Car is a single turbo N54 was driving fine all day parked it at night and now it wont start, it just cranks over. It seems to me like it is a DME failure but I don't want to throw parts at it so any help would be appreciated I attached some pictures of the original fault codes that I got then I cleared them and got almost of them back. I removed the JB4 to narrow down any culprits. I originally tried to read codes through the JB4 but I could not connect and I could not access the steering wheel controls either. Only way I was able to see the codes was through the OBD port on MHD. I attached images of the error codes in the link Thank you !

(#2)
Old
dmikhael619 dmikhael619 is offline
New Member
 
Posts: 10
Join Date: Aug 2016
Car: 2008 e92 335i
Default 11-18-2019, 11:23 AM

If anyone is interested I put a new DME in the car, put in a new engine harness, check every ground, a new JBE module. tested my relays and still no luck. Same codes. I'm pretty much done with this platform. I will be buying an F80 next weekand will be doing a full part-out of a 6mt N54 Black sapphire e92. Doc race 6266 kit makes about 730 whp has about 20k in mods done to it will be listing everything soon. Thank you to everyone in this forum who contributes!
(#3)
Old
Dave @ BMS/Fuel-It!'s Avatar
Dave @ BMS/Fuel-It! Dave @ BMS/Fuel-It! is offline
Super Moderator
 
Posts: 8,484
Join Date: Apr 2014
Car: E92 335XI
Default 11-18-2019, 04:56 PM

Quote:
Originally Posted by dmikhael619
Could use a bit of help. Car is a single turbo N54 was driving fine all day parked it at night and now it wont start, it just cranks over. It seems to me like it is a DME failure but I don't want to throw parts at it so any help would be appreciated I attached some pictures of the original fault codes that I got then I cleared them and got almost of them back. I removed the JB4 to narrow down any culprits. I originally tried to read codes through the JB4 but I could not connect and I could not access the steering wheel controls either. Only way I was able to see the codes was through the OBD port on MHD. I attached images of the error codes in the link Thank you !

I donít see any images..

F80 isnít a bad upgrade choice either


Burger Motorsports
Home of the JB4 the worlds most popular turbocharged tuning system!

It is the sole responsibility of the purchaser and installer of any BMS part to employ the correct installation techniques required to ensure the proper operation of BMS parts, and BMS disclaims any and all liability for any part failure due to improper installation or use. It is the sole responsibility of the customer to verify that the use of their vehicle and items purchased comply with federal, state and local regulations. BMS claims no legal federal, state or local certification concerning pollution controlled motor vehicles or mandated emissions requirements. BMS products labeled for use only in competition racing vehicles may only be used on competition racing vehicles operated exclusively on a closed course in conjunction with a sanctioned racing event, in accordance with all federal and state laws, and may never be operated on public roads/highways. Please click here for more information on legal requirements related to use of BMS parts.
(#4)
Old
Milehighbmw Milehighbmw is offline
Junior Member
 
Posts: 88
Join Date: Aug 2019
Car: 07 335xi
Default 11-18-2019, 07:00 PM

Quote:
Originally Posted by dmikhael619
Could use a bit of help. Car is a single turbo N54 was driving fine all day parked it at night and now it wont start, it just cranks over. It seems to me like it is a DME failure but I don't want to throw parts at it so any help would be appreciated I attached some pictures of the original fault codes that I got then I cleared them and got almost of them back. I removed the JB4 to narrow down any culprits. I originally tried to read codes through the JB4 but I could not connect and I could not access the steering wheel controls either. Only way I was able to see the codes was through the OBD port on MHD. I attached images of the error codes in the link Thank you !

I'm starting over with another e92. When you get a part list with prices together let me know. Ready to purchase alot of stuff. Like I said starting over with a completely stock 335.
(#5)
Old
dmikhael619 dmikhael619 is offline
New Member
 
Posts: 10
Join Date: Aug 2016
Car: 2008 e92 335i
Default 11-24-2019, 05:23 PM

Quote:
Originally Posted by Milehighbmw
I'm starting over with another e92. When you get a part list with prices together let me know. Ready to purchase alot of stuff. Like I said starting over with a completely stock 335.
FULL 6266 335I PARTOUT - N54Tech.com - International Turbo Racing Discussion

here you go sir! Thanks and good luck with the build
Closed Thread


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump




vBulletin Skin developed by: vBStyles.com
Copyright © 2007 - 2020, N54tech.com