2016 Q50 3.0t Prem on 93 octane and Map 6 - JB4tech.com

Sideways the Seven · 2019-12-02 07_14_06_Map-6.csv (412.5 KB, 234 views)

Hello guys, new member here.

Looking for some feedback on my logs. Been looking for ideal settings for my application. I've been running 93 octane but have easy access to E85, if I need that as well. I appreciate any help or direction you guys can give. Thanks!

Lonmon · 02:25 PM

I can't use this log. There is way too much and I can't find a decent pull quickly. You need to go out and find a good flat stretch of road, start in second gear around 2500 rpms, start the log then go full throttle till the car gets well into 4th gear (SAFELY!!). Then let us look at the log. You can do this a couple of times if you like just to make sure to get some good data. The partial throttle info just makes it difficult to find what we need to see, especially when the log is very long. Most logs only need to be 30 seconds or less. At this level of modification the partial throttle information is not too important unless we are trying to diagnose a specific issue. I would not go beyond +6 in your map until we verify that everything looks good, especially when only on 93.

Lonmon · 12-02-2019, 02:24 PM

Look at the map from Serstylz2 on page 197 of the top topic. Use this map but replace the 7's with 6's until we look at the logs. Then if everything looks good you can insert the +7's and let us look at the logs again.

Sideways the Seven · 12-02-2019, 02:31 PM

Quote:

Originally Posted by Lonmon

I can't use this log...

Quote:

Originally Posted by Lonmon

Look at the map from Serstylz2 on page 197 of the top topic. Use this map but replace the 7's with 6's until we look at the logs. Then if everything looks good you can insert the +7's and let us look at the logs again.

Will do. Thanks for the quick reply!

Sideways the Seven · 12-03-2019, 10:47 AM

Updated. Here are the new logs. Thank you!

Terry @ BMS · 12-03-2019, 01:34 PM

Keep in mind tuning is disabled until engine is warmed up. The warmed up log looks OK to me though at first glance.

Sideways the Seven · 12-03-2019, 01:43 PM

Quote:

Originally Posted by Terry @ BMS

Keep in mind tuning is disabled until engine is warmed up. The warmed up log looks OK to me though at first glance.

Ah, good to know, thank you!

I'm still learning about this platform. I appreciate the feedback!

Sideways the Seven · 12-05-2019, 08:33 AM

Found a nice clear road to get a really good pull last night. How do these look? If I'm reading this correctly, everything looks okay.

JS q50 · **Map 6 log check? -** 05-07-2022, 11:12 AM

I am running on 93 octane map 6, 6 psi peak can someone take a look and let me know if I’m good

JCB · 05-08-2022, 06:55 AM

Looks pretty dialed in....you could try adding +1 more psi and see how she does...also you can do your pull in 3rd gear so your not moving so fast.

JS q50 · 05-13-2022, 12:50 PM

Turned up 1 psi… 7 psi please let me know if I’m good

JCB · Yesterday, 07:12 AM

I would back it down to 6.5 at 5000 RPM. I am seeing very low timing values (Ign1 field) right at that RPM level. Also your trims are maxed (reading of 44 on our platform). Not alarming because your AFR still looks fine...just shows you are reaching max for fuel delivery to support that level of boost. If you have the fuel wires, it will help regulate it a bit and bring the trims down.