[ddnspider]

Originally Posted by Serstylz2

Anyone else experiencing problems with the app? 2nd time in 2 days, I start it up and it loads to Map 5 correctly buy shows my Target (additional PSI request) as 0 instead of 5

Is that at WOT? By the looks of the AFR youre either on decel or in lean spool mode.

[Serstylz2]

Originally Posted by ddnspider

Is that at WOT? By the looks of the AFR youre either on decel or in lean spool mode.

Either sitting in my driveway or just pulling off. Was just trying to capture a screenshot of the Target parameter. It fixes if you change to a different map (will still say 0) then back to the original map.

[ddnspider]

Originally Posted by Serstylz2

Anyone else experiencing problems with the app? 2nd time in 2 days, I start it up and it loads to Map 5 correctly buy shows my Target (additional PSI request) as 0 instead of 5

You're not going to see a target boost at idle or cruise because the car isn't trying to make boost. You have to be at WOT to see the target go above 0.

[Serstylz2]

That's strange, it used to show me 5 at all times at Map 5. Also, if I switch off that map to another map then back to map 5, while sitting still, it'll show me 5. I'll take a video shortly

[ddnspider]

Originally Posted by Serstylz2

That's strange, it used to show me 5 at all times at Map 5. Also, if I switch off that map to another map then back to map 5, while sitting still, it'll show me 5. I'll take a video shortly

That sounds like a firmware bug. I just pulled my log from the drag strip and looked at the target and it didn't sit at a constant number.

[Serstylz2]

Originally Posted by Silversport22

Here is the link. Is the the legit JB4 direct from you guys?
https://rover.ebay.com/rover/0/0/0?m...2F264148692109

Yea that's them

[Terry @ BMS]

Originally Posted by Serstylz2

Either sitting in my driveway or just pulling off. Was just trying to capture a screenshot of the Target parameter. It fixes if you change to a different map (will still say 0) then back to the original map.

The target shown at idle will vary based on firmware. At some point we had target showing if pedal input was 0 (e.g. at idle) for informational purposes but not sure how we left it in the latest version.

[Esco]

Question Terry,

Noticed that on the jb4 mobile app there is an option for "CANFlap". I'm assuming this currently does not apply to us.

[jayhawk91]

Hello Terry,

Would you mind taking a look at a couple of my logs and seeing if there is anything of concern? 2017 Silver sport with AMS LDP and Fast Intentions CBE running 93 octane. Boost is set to 8.0 from 3500-5500 rpm and tapers off to +0 at 7000. Thank you!

[Serstylz2]

Without even looking, boost set to 8.0 needs to be changed

[djslug2000]

Anyone know what the SS times are for 1/4 mile with jb4 Pump gas

[Terry @ BMS]

Originally Posted by jayhawk91

Hello Terry,

Would you mind taking a look at a couple of my logs and seeing if there is anything of concern? 2017 Silver sport with AMS LDP and Fast Intentions CBE running 93 octane. Boost is set to 8.0 from 3500-5500 rpm and tapers off to +0 at 7000. Thank you!

I think you'll be better off on map5 here.

[ddnspider]

Originally Posted by djslug2000

Anyone know what the SS times are for 1/4 mile with jb4 Pump gas

highly dependent on the setup and other mods. I went 12.4 with ********* and WMI in not very good air.

[Serstylz2]

Originally Posted by djslug2000

Anyone know what the SS times are for 1/4 mile with jb4 Pump gas

RWD/AWD changes the responses

[ddnspider]

Originally Posted by Serstylz2

RWD/AWD changes the responses

^^^True this!!! The AWD's are running better times due to better 60fts.

[g0t2bmiirii]

Originally Posted by ddnspider

^^^True this!!! The AWD's are running better times due to better 60fts.

AWD should be slightly better on a 0-60.

[ddnspider]

Originally Posted by g0t2bmiirii

AWD should be slightly better on a 0-60.

Yeah, that's the world of drag racing. Whomever gets out quicker typically runs faster/quicker. AWD even with the weight penalty are putting the power down better so running quicker times. Get some drag radials on a RWD and its a different story.

[Serstylz2]

About 3000 miles on these intakes, 4019 miles total on the car. Should I be. concerned?

[Terry @ BMS]

Fairly typical in some climates, they get a lot of airflow! You can clean every 10k-15k miles with a S&B (or any) filter cleaning kit.

https://www.burgertuning.com/product...ning-oil-kit-1

[Serstylz2]

Originally Posted by Terry @ BMS

Fairly typical in some climates, they get a lot of airflow! You can clean every 10k-15k miles with a S&B (or any) filter cleaning kit.

https://www.burgertuning.com/product...ning-oil-kit-1

Thanks, I'll pick that up since you all saved me some cash on the maf housing

[ddnspider]

Just keep rotating the filter until all sides are dirty

[vietnameeh]

I am not sure why I am such a wuss to do a pull lol

but I tried to log on a freeway onramp

This 2019 Luxe stock 91 Octane Map 1 and fuel wires

I also uploaded a random Map 0 to see how the car works stock

everything look ok? could I try map 2 next?!

It's getting warmer here in CA so I am little hesitant

sorry if the logs suck, I can take another if needed lol

Thanks!

[Terry @ BMS]

Originally Posted by vietnameeh

I am not sure why I am such a wuss to do a pull lol

but I tried to log on a freeway onramp

This 2019 Luxe stock 91 Octane Map 1 and fuel wires

I also uploaded a random Map 0 to see how the car works stock

everything look ok? could I try map 2 next?!

It's getting warmer here in CA so I am little hesitant

sorry if the logs suck, I can take another if needed lol

Thanks!

Looks fine to me on map1!

[vietnameeh]

Originally Posted by Terry @ BMS

Looks fine to me on map1!

Thanks! Map 2 next!

[Serstylz2]

Originally Posted by ddnspider

Just keep rotating the filter until all sides are dirty