N54Tech.com - International Turbo Racing Discussion
(#1)
Old
George @ BMS's Avatar
George @ BMS George @ BMS is offline
Legend
 
Posts: 1,212
Join Date: Aug 2009
Car: E90 BMW 335i AT
Default Audi 3.0T Supercharged - 08-13-2020, 03:14 PM

Reserved.


2014 VW Golf 7 R
2014 VW Golf GTI
2019 Porsche Cayenne Turbo
Reply With Quote
(#2)
Old
Mike_L's Avatar
Mike_L Mike_L is offline
Anti-Social
 
Posts: 1,857
Join Date: Jun 2014
Car: 2017 X3 xDrive35i
Default 08-13-2020, 05:31 PM

You're gonna get huge power out of this motor. I ran a RaceChip on my 13 A6 3.0T and made a huge amount of power with it. Probably 70+hp. Audi limits the boost with the ECU, the hardware from all versions are the same, so changing that allows it to make significantly more power. Obviously the 310hp versions will make more than the 335hp or 354hp versions, because they're starting lower and ending up at the same point.


Mike Levy
2021 Tanzanite Blue II M550i - Due at dealer 10/9
2018 Silver Equinox LT 2.0T
Reply With Quote
(#3)
Old
J_from_France J_from_France is offline
New Member
 
Posts: 2
Join Date: Aug 2020
Car: audi S4 B8,5 351hp 466 nm on test bench orgine
Default 08-13-2020, 11:33 PM

Hello, i follow the thread.
i m from france, i buy an audi S4 B8,5 from 2014 ( facelift) S-tronic 7 ( dsg)
moteur CGWC on paper 333 hp and 440 nm vs 351 hp and 466 nm on dyno
feed with 98 ron
i m looking for jb4 and for awe exhaust with oem dp

with jb4 i have to put it on setting n 3 ? right ?
for controle technique ( sorry for english) they plug they computer on obd, so if jb4 obd is unplugged, car run like oem or i need to uninstall all the system before control technique ?

thanks you
Reply With Quote
(#4)
Old
George @ BMS's Avatar
George @ BMS George @ BMS is offline
Legend
 
Posts: 1,212
Join Date: Aug 2009
Car: E90 BMW 335i AT
Default 08-15-2020, 08:31 AM

Quote:
Originally Posted by J_from_France
Hello, i follow the thread.
i m from france, i buy an audi S4 B8,5 from 2014 ( facelift) S-tronic 7 ( dsg)
moteur CGWC on paper 333 hp and 440 nm vs 351 hp and 466 nm on dyno
feed with 98 ron
i m looking for jb4 and for awe exhaust with oem dp

with jb4 i have to put it on setting n 3 ? right ?
for controle technique ( sorry for english) they plug they computer on obd, so if jb4 obd is unplugged, car run like oem or i need to uninstall all the system before control technique ?

thanks you
On current firmware on the unit if you unplug the OBD it still adds 2psi. I am not sure what Controle Technique is but if its to remove it for diagnostic purposes there is no issue with that.
For 98Ron map 3 is recommended.


2014 VW Golf 7 R
2014 VW Golf GTI
2019 Porsche Cayenne Turbo
Reply With Quote
(#5)
Old
J_from_France J_from_France is offline
New Member
 
Posts: 2
Join Date: Aug 2020
Car: audi S4 B8,5 351hp 466 nm on test bench orgine
Default 08-16-2020, 11:20 AM

Quote:
Originally Posted by George @ BMS
On current firmware on the unit if you unplug the OBD it still adds 2psi. I am not sure what Controle Technique is but if its to remove it for diagnostic purposes there is no issue with that.
For 98Ron map 3 is recommended.
Thanks.
Controle technique = technic inspection to be sure véhicule is ok for drive.
And they plug they computer on obd for diagnostic and do at same time test for C02.

So BMS plugged in obd = map 3, i turn off the car, i unplug BMS from obd and get map 1, i go to technic inspection => no problemo ?

After inspection, i turn off the car, plug BMS in obd, map 3 get back ?

sorry for stupid question
Reply With Quote
(#6)
Old
George @ BMS's Avatar
George @ BMS George @ BMS is offline
Legend
 
Posts: 1,212
Join Date: Aug 2009
Car: E90 BMW 335i AT
Default 08-16-2020, 02:05 PM

Quote:
Originally Posted by J_from_France
Thanks.
Controle technique = technic inspection to be sure véhicule is ok for drive.
And they plug they computer on obd for diagnostic and do at same time test for C02.

So BMS plugged in obd = map 3, i turn off the car, i unplug BMS from obd and get map 1, i go to technic inspection => no problemo ?

After inspection, i turn off the car, plug BMS in obd, map 3 get back ?

sorry for stupid question
Yes, this is possible. At idle and light load where most testing is done the emissions will not change at all and be in line.


2014 VW Golf 7 R
2014 VW Golf GTI
2019 Porsche Cayenne Turbo
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump




vBulletin Skin developed by: vBStyles.com
Copyright © 2007 - 2020, N54tech.com