N54Tech.com - International Turbo Racing Discussion
(#3676)
Old
Creative911 Creative911 is offline
New Member
 
Posts: 4
Join Date: May 2017
Car: F10 535i M Package
Default 05-31-2019, 03:29 PM

Quote:
Originally Posted by Terry @ BMS
It's fine here, add a JB4 log though for any tuning advice!
Here is the log from a pull I just did, only change is that I added E85 (30%).
Attached Images
 
Reply With Quote
(#3677)
Old
Creative911 Creative911 is offline
New Member
 
Posts: 4
Join Date: May 2017
Car: F10 535i M Package
Default 06-12-2019, 10:40 PM

Quote:
Originally Posted by Creative911
Here is the log from a pull I just did, only change is that I added E85 (30%).
Any help on this is greatly appreciated
Reply With Quote
(#3678)
Old
Phataxe's Avatar
Phataxe Phataxe is offline
Junior Member
 
Posts: 162
Join Date: Mar 2018
Car: 2014 435I
Default 06-13-2019, 04:41 AM

Post the actual log not a image of the graph.


'14 435I RWD MHD "Twisted Custom Tune" ° BigBoost Stage 3 Turbo ° PR Coils ° XHP Trans Tune ° GFB DV+ ° VRSF Race Cooler ° VRSF CP ° BMS Intake ° Borla ATAK Exhaust ° Custom Down-pipe ° stage 3 LPFP ° BMP4 EKP ° M Performance LSD ° Phoenix Racing PI Intake Manifold ° AIC2-P controller ° e85 ° 3.5 TMAP ° NGK 5992 Plugs "0.020"
Reply With Quote
(#3679)
Old
135idct 135idct is offline
Junior Member
 
Posts: 444
Join Date: May 2012
Default 06-26-2019, 07:04 PM

try this one
Attached Files
File Type: hex JB4_F_EWG_17_T1.hex (83.3 KB, 66 views)
Reply With Quote
(#3680)
Old
VTR VTR is offline
New Member
 
Posts: 19
Join Date: Feb 2018
Car: bmw e82
Default 07-04-2019, 11:35 AM

What is the latest version of Firmware?
Could someone tell me where to download it?
Thank you!
Reply With Quote
(#3681)
Old
Terry @ BMS's Avatar
Terry @ BMS Terry @ BMS is offline
Tuner
 
Posts: 29,837
Join Date: Jan 2008
Default 07-04-2019, 11:37 AM

Depends on the model car! EWG or PWG. Sig says you have E chassis?? This is F chassis.


Burger Motorsports
Home of the Worlds fastest N20s, N54s, N55s, S55s, N63s, and S63s!

It is the sole responsibility of the purchaser and installer of any BMS part to employ the correct installation techniques required to ensure the proper operation of BMS parts, and BMS disclaims any and all liability for any part failure due to improper installation or use. It is the sole responsibility of the customer to verify that the use of their vehicle and items purchased comply with federal, state and local regulations. BMS claims no legal federal, state or local certification concerning pollution controlled motor vehicles or mandated emissions requirements. BMS products labeled for use only in competition racing vehicles may only be used on competition racing vehicles operated exclusively on a closed course in conjunction with a sanctioned racing event, in accordance with all federal and state laws, and may never be operated on public roads/highways. Please click here for more information on legal requirements related to use of BMS parts.
Reply With Quote
(#3682)
Old
5soko's Avatar
5soko 5soko is offline
Vintage
 
Posts: 288
Join Date: Apr 2008
Car: F10 N55 PWG
Default 07-04-2019, 06:22 PM

Loading up the latest PWG firmware.. How has it been working for everyone?

Im assuming the default N55 settings and the duty bias values are for PWG aswell?


2014 F10 535i N55 PWG
Reply With Quote
(#3683)
Old
e46m3to335i's Avatar
e46m3to335i e46m3to335i is offline
Junior Member
 
Posts: 283
Join Date: Feb 2010
Car: 2015 F22 M235i
Default 07-09-2019, 02:24 PM

Is it possible to monitor Meth flow and Ethanol content at the same time on the App? I'm guessing not since both require pin 16 for signal. Just trying to confirm


2014 335i xDrive / Silver / ZF8 / M-Sport / 400M / BM3 2H Map / xHP Stage 3 / ATM FMIC / H&R Sports / VRSF **/CP
Reply With Quote
(#3684)
Old
Terry @ BMS's Avatar
Terry @ BMS Terry @ BMS is offline
Tuner
 
Posts: 29,837
Join Date: Jan 2008
Default 07-09-2019, 05:05 PM

Quote:
Originally Posted by e46m3to335i
Is it possible to monitor Meth flow and Ethanol content at the same time on the App? I'm guessing not since both require pin 16 for signal. Just trying to confirm
Yes, it is. There are alternative E85 inputs. For EWG systems we have a V2 board now that has an extra analog input on the DB9 for low fuel pressure or E85 for cars equipped with WMI (that already uses the 2 extra DB25 connections)


Burger Motorsports
Home of the Worlds fastest N20s, N54s, N55s, S55s, N63s, and S63s!

It is the sole responsibility of the purchaser and installer of any BMS part to employ the correct installation techniques required to ensure the proper operation of BMS parts, and BMS disclaims any and all liability for any part failure due to improper installation or use. It is the sole responsibility of the customer to verify that the use of their vehicle and items purchased comply with federal, state and local regulations. BMS claims no legal federal, state or local certification concerning pollution controlled motor vehicles or mandated emissions requirements. BMS products labeled for use only in competition racing vehicles may only be used on competition racing vehicles operated exclusively on a closed course in conjunction with a sanctioned racing event, in accordance with all federal and state laws, and may never be operated on public roads/highways. Please click here for more information on legal requirements related to use of BMS parts.
Reply With Quote
(#3685)
Old
e46m3to335i's Avatar
e46m3to335i e46m3to335i is offline
Junior Member
 
Posts: 283
Join Date: Feb 2010
Car: 2015 F22 M235i
Default 07-09-2019, 05:33 PM

Quote:
Originally Posted by Terry @ BMS
Yes, it is. There are alternative E85 inputs. For EWG systems we have a V2 board now that has an extra analog input on the DB9 for low fuel pressure or E85 for cars equipped with WMI (that already uses the 2 extra DB25 connections)

Thanks for the reply Terry,


Do you have a link for the V2 EWG board? I can't find it on the BMS website. Just to confirm, in order to monitor ethanol content and WMI, the V2 board is required?


2014 335i xDrive / Silver / ZF8 / M-Sport / 400M / BM3 2H Map / xHP Stage 3 / ATM FMIC / H&R Sports / VRSF **/CP
Reply With Quote
(#3686)
Old
Ultra_435xi Ultra_435xi is offline
New Member
 
Posts: 7
Join Date: Nov 2018
Car: F32 435i xdrive
Default 07-14-2019, 04:50 AM

What is the latest firmware for Ewg ? Ewg 17 t2 or ewg 16 test5 ? Im a little bit confused.


Greetings from Germany

435i xdrive
Reply With Quote
(#3687)
Old
e46m3to335i's Avatar
e46m3to335i e46m3to335i is offline
Junior Member
 
Posts: 283
Join Date: Feb 2010
Car: 2015 F22 M235i
Default 07-15-2019, 09:21 AM

Quote:
Originally Posted by Terry @ BMS
Yes, it is. There are alternative E85 inputs. For EWG systems we have a V2 board now that has an extra analog input on the DB9 for low fuel pressure or E85 for cars equipped with WMI (that already uses the 2 extra DB25 connections)
Quote:
Originally Posted by e46m3to335i
Thanks for the reply Terry,


Do you have a link for the V2 EWG board? I can't find it on the BMS website. Just to confirm, in order to monitor ethanol content and WMI, the V2 board is required?
??


2014 335i xDrive / Silver / ZF8 / M-Sport / 400M / BM3 2H Map / xHP Stage 3 / ATM FMIC / H&R Sports / VRSF **/CP
Reply With Quote
(#3688)
Old
rusty13 rusty13 is offline
New Member
 
Posts: 6
Join Date: Feb 2017
Car: BMW M135i
Default 07-15-2019, 01:12 PM

What’s the firmware change log for EWG 17 t2?
Reply With Quote
(#3689)
Old
JLBimmer's Avatar
JLBimmer JLBimmer is offline
Junior Member
 
Posts: 56
Join Date: Jun 2019
Car: 2016 435ix GC
Default 07-15-2019, 01:50 PM

Hey Terry is there a way to fix the Fault code that comes with the EWG harness? I am getting them randomly. I have been practicing the ACC on before Start trick but still is comes up from several times a week at start


JL Bimmer
2016 435ix Gran Coupe
HRP Cold Air Intake, Charge Pipe, Turbo Up Pipe, Turbo Intake Pipe, BMS Intercooler, Axle Back Exhaust, JB4
H&R Springs, Sways, Strut Tower bar, 19"x10 Rotiforms, Too much carbon goodness
Reply With Quote
(#3690)
Old
Lipper Lipper is offline
New Member
 
Posts: 12
Join Date: May 2018
Car: 2015 M235i 6MT
Default EWG 17 t2 - 07-15-2019, 08:27 PM

Are there release notes for the new version? I'm running EWG 15 and wondering if it's worth the upgrade.

Thanks - Ken
Reply With Quote
(#3691)
Old
Endeav Endeav is offline
Junior Member
 
Posts: 88
Join Date: Sep 2017
Car: BMW M2
Default 07-16-2019, 07:42 AM

Quote:
Originally Posted by Lipper
Are there release notes for the new version? I'm running EWG 15 and wondering if it's worth the upgrade.

Thanks - Ken
Also interested in the release notes!

Thanks BMS for all these updates!


'17 BMW M2 - [DCT/N55] - PureTurbos Stage 2 Turbo - JB4 + MHD BEF - Fuel-It Methanol PI
Reply With Quote
(#3692)
Old
tauzins tauzins is offline
Junior Member
 
Posts: 38
Join Date: Aug 2017
Car: 2014 335i m-sport
Default 07-16-2019, 01:05 PM

Quote:
Originally Posted by Endeav
Also interested in the release notes!

Thanks BMS for all these updates!
Agreed, i didnt even know there was a new version because i always looked at the notes to see if a new ver. came out.


F30 335i | ER Chargepipe | ER Down-Pipe | Wagner Intercooler | BMS Intake | Meisterschaft Exhaust | MHD BEF JB4 Map 3 / 30% e85 / 50:50 Meth
Reply With Quote
(#3693)
Old
sdhasher21 sdhasher21 is offline
New Member
 
Posts: 26
Join Date: Jan 2019
Car: 2016 M235i
Default 07-19-2019, 05:05 PM

Quote:
Originally Posted by tauzins
Agreed, i didnt even know there was a new version because i always looked at the notes to see if a new ver. came out.
Likewise. Would love to update this weekend, depending on what the changes are.
Reply With Quote
(#3694)
Old
nobu5552 nobu5552 is offline
New Member
 
Posts: 6
Join Date: Feb 2017
Car: F10 535i
Default 07-22-2019, 08:04 AM

I tried using 17 firmware. However, the boost was 27 PSI with the 7th to 8th speed half accelerator in high gear. I thought that the engine would break. DME error code 101f02 was also issued. I think it is better not to use it because it is dangerous.


2014 535i / ZF 8 / M-Sport / MHD Back-end Flash / XHP Stage 3 / AT / ** / Valve Straight Muffler / FTP Boost Turbo Pipe / Wagner Intercooler /
BMS intake / forge valve

Last edited by nobu5552; 07-22-2019 at 08:12 AM..
Reply With Quote
(#3695)
Old
e46m3to335i's Avatar
e46m3to335i e46m3to335i is offline
Junior Member
 
Posts: 283
Join Date: Feb 2010
Car: 2015 F22 M235i
Default 07-22-2019, 08:21 AM

Quote:
Originally Posted by nobu5552
I tried using 17 firmware. However, the boost was 27 PSI with the 7th to 8th speed half accelerator in high gear. I thought that the engine would break. DME error code 101f02 was also issued. I think it is better not to use it because it is dangerous.


2014 535i / ZF 8 / M-Sport / MHD Back-end Flash / XHP Stage 3 / AT / ** / Valve Straight Muffler / FTP Boost Turbo Pipe / Wagner Intercooler /
BMS intake / forge valve
Yikes!!


2014 335i xDrive / Silver / ZF8 / M-Sport / 400M / BM3 2H Map / xHP Stage 3 / ATM FMIC / H&R Sports / VRSF **/CP
Reply With Quote
(#3696)
Old
smahel smahel is offline
New Member
 
Posts: 28
Join Date: Apr 2008
Car: 335Ci
Default 07-23-2019, 03:01 AM

I tried the EWG 17 T2 too, the map 6 that I use, seems to me much less consistent, the boost was like usually, no codes. After turning off the car, the firmware forgets some in dash settings. So I'm back on the EWG 16 T5. Here is everything O.K.
Reply With Quote
(#3697)
Old
5soko's Avatar
5soko 5soko is offline
Vintage
 
Posts: 288
Join Date: Apr 2008
Car: F10 N55 PWG
Default 07-23-2019, 01:23 PM

Quote:
Originally Posted by nobu5552
I tried using 17 firmware. However, the boost was 27 PSI with the 7th to 8th speed half accelerator in high gear. I thought that the engine would break. DME error code 101f02 was also issued. I think it is better not to use it because it is dangerous.


2014 535i / ZF 8 / M-Sport / MHD Back-end Flash / XHP Stage 3 / AT / ** / Valve Straight Muffler / FTP Boost Turbo Pipe / Wagner Intercooler /
BMS intake / forge valve
Isnt all 2014 535i's PWG?


2014 F10 535i N55 PWG
Reply With Quote
(#3698)
Old
nobu5552 nobu5552 is offline
New Member
 
Posts: 6
Join Date: Feb 2017
Car: F10 535i
Default 07-24-2019, 06:28 AM

Quote:
Originally Posted by 5soko
Isnt all 2014 535i's PWG?
My car is an EWG vehicle. The use of the 17EWG firmware was really scary.:eek:


2014 535i / ZF 8 / M-Sport / MHD Back-end Flash / XHP Stage 3 / AT / ** / Valve Straight Muffler / FTP Boost Turbo Pipe / Wagner Intercooler /
BMS intake / forge valve
Reply With Quote
(#3699)
Old
mversi mversi is offline
New Member
 
Posts: 3
Join Date: Mar 2019
Car: 2017 BMW M2 LCI DCT
Default 07-25-2019, 05:02 PM

Anyone running firmware 17_T2 on a N55 M2? I have a Wagner ** & IC and BMS intake and the car only seems to be hitting 14PSI on Map2, same as it's getting on Map0 !
Reply With Quote
(#3700)
Old
tpayne1305@gmail.com tpayne1305@gmail.com is offline
New Member
 
Posts: 1
Join Date: Jul 2019
Car: 2014 F10
Smile User Adjustment N55 Default Settings - 07-31-2019, 03:12 PM

Do I input the N55 Default Settings parameters that are attached to the F Chassis N55 JB4 page into the User Adjustment tab via the iPhone? New to this so I just want to make sure all is set up right...I uploaded the new version of Firmware and selected Map 5 to run. Please assist with the above question, thanks!
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 7 (0 members and 7 guests)
 
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump




vBulletin Skin developed by: vBStyles.com
Copyright © 2007 - 2019, N54tech.com