N54Tech.com - International Turbo Racing Discussion
(#3626)
Old
alo0oy215's Avatar
alo0oy215 alo0oy215 is offline
Junior Member
 
Posts: 33
Join Date: Mar 2017
Car: 2012 f30 335i
Default 12-12-2018, 12:53 AM

Will the new integrated firmware work with a BEF? And what should i do? Only solder the diode and load the firmware?!


N55 powerd 335I sedan :
1- kettyless D P
2- CP
3- Custom exhaust
4- JB4 + FF wires
5- BMS F30 N55 Performance Intake
6- BMS WMI KIT
Reply With Quote
(#3627)
Old
Bsbllfit7 Bsbllfit7 is offline
New Member
 
Posts: 19
Join Date: Aug 2018
Car: 2013 535i
Default 12-17-2018, 04:42 PM

Is it recommended to go with the integrated Version 12 t2 or should we be going to ISO and cut the diode?
Reply With Quote
(#3628)
Old
tomerz tomerz is offline
New Member
 
Posts: 2
Join Date: May 2018
Car: 2014 m235i
Default explanation - 12-21-2018, 12:08 AM

Hello everyone where can i find a detailed explanation for the JB4-APP
Reply With Quote
(#3629)
Old
tomerz tomerz is offline
New Member
 
Posts: 2
Join Date: May 2018
Car: 2014 m235i
Default ??? - 12-23-2018, 03:10 AM

Quote:
Originally Posted by tomerz
Hello everyone where can i find a detailed explanation for the JB4-APP
???
Reply With Quote
(#3630)
Old
rallyrafa rallyrafa is offline
Junior Member
 
Posts: 41
Join Date: Dec 2018
Car: 535i GT 2011
Default 6-cyl timing - 12-23-2018, 08:53 PM

@terry
Can we have the ISO function of "6-cyl timing logging" to be "gas pedal aggressiveness" too? Or it's already in the integrated?
Or it's exclusive of ISO?


2011 535i f07 custom pipe after turbo, VRSF CP, K&N CAI, E40+ BEF
Reply With Quote
(#3631)
Old
Terry @ BMS's Avatar
Terry @ BMS Terry @ BMS is offline
Tuner
 
Posts: 32,579
Join Date: Jan 2008
Default 12-23-2018, 10:18 PM

Quote:
Originally Posted by Bsbllfit7
Is it recommended to go with the integrated Version 12 t2 or should we be going to ISO and cut the diode?
For PWG, 12_T2.


Burger Motorsports
Home of the JB4 the worlds most popular turbocharged tuning system!

It is the sole responsibility of the purchaser and installer of any BMS part to employ the correct installation techniques required to ensure the proper operation of BMS parts, and BMS disclaims any and all liability for any part failure due to improper installation or use. It is the sole responsibility of the customer to verify that the use of their vehicle and items purchased comply with federal, state and local regulations. BMS claims no legal federal, state or local certification concerning pollution controlled motor vehicles or mandated emissions requirements. BMS products labeled for use only in competition racing vehicles may only be used on competition racing vehicles operated exclusively on a closed course in conjunction with a sanctioned racing event, in accordance with all federal and state laws, and may never be operated on public roads/highways. Please click here for more information on legal requirements related to use of BMS parts.
Reply With Quote
(#3632)
Old
Terry @ BMS's Avatar
Terry @ BMS Terry @ BMS is offline
Tuner
 
Posts: 32,579
Join Date: Jan 2008
Default 12-23-2018, 10:19 PM

Quote:
Originally Posted by rallyrafa
@terry
Can we have the ISO function of "6-cyl timing logging" to be "gas pedal aggressiveness" too? Or it's already in the integrated?
Or it's exclusive of ISO?
Pedal aggressiveness is menu10 in dash with PWG_12, 0-5000 = 0 - 100%


Burger Motorsports
Home of the JB4 the worlds most popular turbocharged tuning system!

It is the sole responsibility of the purchaser and installer of any BMS part to employ the correct installation techniques required to ensure the proper operation of BMS parts, and BMS disclaims any and all liability for any part failure due to improper installation or use. It is the sole responsibility of the customer to verify that the use of their vehicle and items purchased comply with federal, state and local regulations. BMS claims no legal federal, state or local certification concerning pollution controlled motor vehicles or mandated emissions requirements. BMS products labeled for use only in competition racing vehicles may only be used on competition racing vehicles operated exclusively on a closed course in conjunction with a sanctioned racing event, in accordance with all federal and state laws, and may never be operated on public roads/highways. Please click here for more information on legal requirements related to use of BMS parts.
Reply With Quote
(#3633)
Old
rallyrafa rallyrafa is offline
Junior Member
 
Posts: 41
Join Date: Dec 2018
Car: 535i GT 2011
Default 12-24-2018, 07:07 AM

@terry
What is menu9?
Cant find anywhere


2011 535i f07 custom pipe after turbo, VRSF CP, K&N CAI, E40+ BEF
Reply With Quote
(#3634)
Old
Marlinman's Avatar
Marlinman Marlinman is offline
Junior Member
 
Posts: 316
Join Date: Jul 2014
Car: 335i coupe 2010
Default 12-24-2018, 08:31 AM

Quote:
Originally Posted by rallyrafa
@terry
What is menu9?
Cant find anywhere
Read some of the forum sticky threads, watch videos, etc. it is all in there.


2013 335xi PWG, JB4, CP, meow-less pipe, FMIC, PS2 with DV/inlet, stock fueling, stock intake
Reply With Quote
(#3635)
Old
Terry @ BMS's Avatar
Terry @ BMS Terry @ BMS is offline
Tuner
 
Posts: 32,579
Join Date: Jan 2008
Default 12-24-2018, 10:05 AM

Quote:
Originally Posted by rallyrafa
@terry
What is menu9?
Cant find anywhere
Base dutycycle but isn't used on PWG_INT.


Burger Motorsports
Home of the JB4 the worlds most popular turbocharged tuning system!

It is the sole responsibility of the purchaser and installer of any BMS part to employ the correct installation techniques required to ensure the proper operation of BMS parts, and BMS disclaims any and all liability for any part failure due to improper installation or use. It is the sole responsibility of the customer to verify that the use of their vehicle and items purchased comply with federal, state and local regulations. BMS claims no legal federal, state or local certification concerning pollution controlled motor vehicles or mandated emissions requirements. BMS products labeled for use only in competition racing vehicles may only be used on competition racing vehicles operated exclusively on a closed course in conjunction with a sanctioned racing event, in accordance with all federal and state laws, and may never be operated on public roads/highways. Please click here for more information on legal requirements related to use of BMS parts.
Reply With Quote
(#3636)
Old
zookerjr5 zookerjr5 is offline
New Member
 
Posts: 17
Join Date: Apr 2018
Car: 2012 335i F30
Default 12-28-2018, 10:50 AM

I downloaded and updated to the new PWG_T2 and not much is lining up. The OBDII menu does not match what is listed. For example the menu with boost on fuel gauge and AFR on speedo only has two options not 4.

Will this be updated?
Reply With Quote
(#3637)
Old
sabujan sabujan is offline
Junior Member
 
Posts: 32
Join Date: Feb 2015
Car: 335i f30 2012
Default 12-29-2018, 01:28 AM

Hi Terry -on my car N55_F_PWG_INT_12 - menu10 when set to any value above 0 - through in dash shows transmission error - with 0 no issues
Reply With Quote
(#3638)
Old
Fmonteiro444's Avatar
Fmonteiro444 Fmonteiro444 is offline
Senior Member
 
Posts: 639
Join Date: Aug 2013
Car: 09 E92 SG
Default 01-02-2019, 10:58 AM

Terry I tried firmware JB4_F_EWG_16_TEST5 on my big turbo setup and it did not run well. I also noticed any time I let off the gas or was at a complete stop the target boost was always 14.2psi.
Attached Files
File Type: csv 2018-12-24 11_18_53_Gear-5_Map-6.csv (3.3 KB, 137 views)
File Type: csv 2018-12-24 11_19_02_Gear-6_Map-6.csv (3.4 KB, 150 views)
File Type: csv 2018-12-24 11_28_43_Gear-6_Map-6.csv (2.8 KB, 146 views)
File Type: csv 2018-12-24 11_36_22_Gear-4_Map-6.csv (7.1 KB, 120 views)


----------------------------------------------------
14 F30 335xi AT- Built Closed-Deck N55, SpeedTech Stage 3 w/ BW-8374C, MHD Flash, xHP Flash, E85, AFE Intake, VRSF 6" Race FMIC, VRSF CP, Fuel-it Stage 2 LPFP and PI
----------------------------------------------------
16 Audi S6 - APR Stage 2 ECU/TCU flash, APR Exhaust, SRM Intakes
Reply With Quote
(#3639)
Old
Ldenne123's Avatar
Ldenne123 Ldenne123 is offline
New Member
 
Posts: 17
Join Date: May 2018
Car: M135i 2014 EWG JB4 MAP 2 + MHD BEF *****
Default 01-05-2019, 06:06 PM

Hi there I am booked in for a rolling road i was wondering do they need to use the obd for this as the obd port is used already for the jb4 , as I understand if I disconnect this will disable my map and won't have the power for the dyno ?

Thanks ..
Reply With Quote
(#3640)
Old
rallyrafa rallyrafa is offline
Junior Member
 
Posts: 41
Join Date: Dec 2018
Car: 535i GT 2011
Default 01-06-2019, 10:52 AM

@Terry
Hi terry, i'm achieving sucessfully content of e42, can i try e50 or more?
The Log show the pump working the same with e42 and e25(Our fuel here starts with e25).
To start with e50 should i change the BEF to E85 mix or can i stick with RACE BEF?


2011 535i f07 custom pipe after turbo, VRSF CP, K&N CAI, E40+ BEF
Reply With Quote
(#3641)
Old
kinetic kinetic is offline
New Member
 
Posts: 8
Join Date: Dec 2016
Car: M135i
Default 01-18-2019, 04:26 PM

After the last firmware update, on mi M135 PWG
The Trans Temp Gauge on the mobile App (Android) stopped working..
it shows "-17". Everything else is working properly..

Name:  IMG_20190118_172520.jpg
Views: 788
Size:  110.3 KB

Last edited by kinetic; 01-20-2019 at 02:00 PM..
Reply With Quote
(#3642)
Old
TwistedX TwistedX is offline
New Member
 
Posts: 29
Join Date: Oct 2016
Car: 2015 BMW X6 35i
Default 01-18-2019, 09:54 PM

Quote:
Originally Posted by kinetic
After the last firmware update, on mi M135 PWG
The Trans Temp Gauge on the mobile App (Android) stop working, it shows - 17 everything else is working properly.. Attachment 82849
You try disconnecting and reconnecring?


Project Succubus - 2015 Estoril Blue M235i F23
Sponsors: SoloWerks, Extreme PowerHouse, and AEM Intake Systems
Reply With Quote
(#3643)
Old
kinetic kinetic is offline
New Member
 
Posts: 8
Join Date: Dec 2016
Car: M135i
Default 01-19-2019, 10:01 AM

Quote:
Originally Posted by TwistedX
You try disconnecting and reconnecring?
I tried that before making that post, and I mean the obd connection, the car and the Bluetooth connection
Reply With Quote
(#3644)
Old
Mannypr24 Mannypr24 is offline
Junior Member
 
Posts: 34
Join Date: May 2015
Car: Bmw 335
Default Drivetrain Malfunction - 01-19-2019, 11:22 AM

Hi, I am on the Iso Firmware.

Having this codes- 120308- Boost pressure lower than expected
And 108F01. What can cause this issues?

Also running mafless.
Attached Images
 


2013 N55 F30- PWG, JB4 ISO_11, CP, MEOW LESS PIPE, FMIC, STOCK TURBO, STOCK INTAKE. 93OCT.
Reply With Quote
(#3645)
Old
Phataxe's Avatar
Phataxe Phataxe is offline
Junior Member
 
Posts: 168
Join Date: Mar 2018
Car: 2014 435I
Default 01-19-2019, 11:27 AM

Quote:
Originally Posted by Mannypr24
Hi, I am on the Iso Firmware.

Having this codes- 120308- Boost pressure lower than expected
And 108F01. What can cause this issues?

Also running mafless.
Wrong area and need to post a log if you wanna get any kinda real advice bud. Try to post in the Support area with a log


'14 435I RWD MHD "Shoup Custom Tune" BigBoost Stage 3 Turbo Spool FX-150 XHP Trans Tune VRSF Race Cooler VRSF CP BMS Intake Borla ATAK Exhaust Custom Down-pipe Stage 3 LPFP BMP4 EKP M Performance LSD Phoenix Racing PI Intake Manifold AIC2-P controller e85 3.5 TMAP NGK 5992 Plugs "0.020"
Reply With Quote
(#3646)
Old
zookerjr5 zookerjr5 is offline
New Member
 
Posts: 17
Join Date: Apr 2018
Car: 2012 335i F30
Default 01-21-2019, 07:20 AM

Quote:
Originally Posted by kinetic
After the last firmware update, on mi M135 PWG
The Trans Temp Gauge on the mobile App (Android) stopped working..
it shows "-17". Everything else is working properly..

Attachment 82849
I have the same problem my trans temp does not work anymore either.
Reply With Quote
(#3647)
Old
kinetic kinetic is offline
New Member
 
Posts: 8
Join Date: Dec 2016
Car: M135i
Default 01-21-2019, 08:10 AM

Quote:
Originally Posted by zookerjr5
I have the same problem my trans temp does not work anymore either.
im starting to think that the problem is the app update, and not the firmware update..
Reply With Quote
(#3648)
Old
rallyrafa rallyrafa is offline
Junior Member
 
Posts: 41
Join Date: Dec 2018
Car: 535i GT 2011
Default 01-21-2019, 06:22 PM

@terry

There will be a new firmware/BEF update for the new released xHP flash tool that supports the new zf8hp?

Or no need for it?


2011 535i f07 custom pipe after turbo, VRSF CP, K&N CAI, E40+ BEF
Reply With Quote
(#3649)
Old
135idct 135idct is offline
Junior Member
 
Posts: 446
Join Date: May 2012
Default 02-01-2019, 09:21 AM

Quote:
Originally Posted by Fmonteiro444
Terry I tried firmware JB4_F_EWG_16_TEST5 on my big turbo setup and it did not run well. I also noticed any time I let off the gas or was at a complete stop the target boost was always 14.2psi.
is ur boost on target when u go WOT? in this firmware?

i run same ur setup EFR8374
Reply With Quote
(#3650)
Old
liuchen333 liuchen333 is offline
New Member
 
Posts: 6
Join Date: Feb 2019
Car: m135i pwg
Default 02-14-2019, 07:55 PM

Quote:
Originally Posted by zookerjr5
I have the same problem my trans temp does not work anymore either.

Hello, brother. I have the same problem. how did you solve it?
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump




vBulletin Skin developed by: vBStyles.com
Copyright 2007 - 2020, N54tech.com