N54Tech.com - International Turbo Racing Discussion
(#151)
Old
Terry @ BMS's Avatar
Terry @ BMS Terry @ BMS is offline
Tuner
 
Posts: 32,354
Join Date: Jan 2008
Default 04-21-2019, 11:40 AM

Quote:
Originally Posted by ThorVanEden
ok..

now i have the 6cyl. timing (5)

last run att.

i tryed map 5 , 6 ,7 ... its the same ... not more than 11PSI
What turbos?


Burger Motorsports
Home of the JB4 the worlds most popular turbocharged tuning system!

It is the sole responsibility of the purchaser and installer of any BMS part to employ the correct installation techniques required to ensure the proper operation of BMS parts, and BMS disclaims any and all liability for any part failure due to improper installation or use. It is the sole responsibility of the customer to verify that the use of their vehicle and items purchased comply with federal, state and local regulations. BMS claims no legal federal, state or local certification concerning pollution controlled motor vehicles or mandated emissions requirements. BMS products labeled for use only in competition racing vehicles may only be used on competition racing vehicles operated exclusively on a closed course in conjunction with a sanctioned racing event, in accordance with all federal and state laws, and may never be operated on public roads/highways. Please click here for more information on legal requirements related to use of BMS parts.
Reply With Quote
(#152)
Old
ThorVanEden ThorVanEden is offline
New Member
 
Posts: 28
Join Date: Aug 2018
Car: Z4 E89 35i +
Default 04-22-2019, 02:07 PM

i have bigger upgrade Turbos
New Chargepipe
*********
Reply With Quote
(#153)
Old
le_roi_leo le_roi_leo is offline
New Member
 
Posts: 11
Join Date: Jun 2019
Car: bmw 135i n55 e82
Default 07-01-2019, 04:44 AM

have a silly question ?
how you know that a log is good ?

he is necessary that the curve PWM and FF coincides?
and that the curve PWM has a minimal oscillation ?
Reply With Quote
(#154)
Old
Payam @ BMS's Avatar
Payam @ BMS Payam @ BMS is offline
Super Moderator
 
Posts: 6,160
Join Date: Oct 2013
Car: e90 335i
Default 07-01-2019, 07:31 AM

Quote:
Originally Posted by le_roi_leo
have a silly question ?
how you know that a log is good ?

he is necessary that the curve PWM and FF coincides?
and that the curve PWM has a minimal oscillation ?
Post a log in the support section and we'll take a look and tell you what to look out for.


Burger Motorsports
Home of the Worlds fastest N20s, N54s, N55s, S55s, N63s, and S63s!

It is the sole responsibility of the purchaser and installer of any BMS part to employ the correct installation techniques required to ensure the proper operation of BMS parts, and BMS disclaims any and all liability for any part failure due to improper installation or use. It is the sole responsibility of the customer to verify that the use of their vehicle and items purchased comply with federal, state and local regulations. BMS claims no legal federal, state or local certification concerning pollution controlled motor vehicles or mandated emissions requirements. BMS products labeled for use only in competition racing vehicles may only be used on competition racing vehicles operated exclusively on a closed course in conjunction with a sanctioned racing event, in accordance with all federal and state laws, and may never be operated on public roads/highways. Please click here for more information on legal requirements related to use of BMS parts.
Reply With Quote
(#155)
Old
le_roi_leo le_roi_leo is offline
New Member
 
Posts: 11
Join Date: Jun 2019
Car: bmw 135i n55 e82
Default 07-02-2019, 04:24 AM

finally, when i read, he show us just than he change the PID for adjust the curve.

but it not know if a PID hight or low is good for your engine ?

if i understand, FF Curve = Internal Mapping * duty bias/50 * FF/100
and terry said #20 than for DUTYBIAS 0 same 50.

so according to the formula:
if (for exemple) all the numbers DB = 65 and the FF =50
it's same than all numbers DB=0 (0=50) and FF=65 (50+15)

but when FUD=0, the setting FF is automatic,
ok you show us the effuences DB PID etc...
but for finally we said us to let FF Jb4 on the automatic setting ?
Reply With Quote
(#156)
Old
Meka11113 Meka11113 is offline
New Member
 
Posts: 1
Join Date: Mar 2020
Car: 2010 bmw 335i
Default 03-10-2020, 07:50 AM

Quote:
Originally Posted by SPANKY
I have the latest firmware and interface.i had my duty bias all set to 0. Then I tried all set to 50,did a log and noticed right away my car would do a bucking throughout 2nd ,3rd and fourth.i pulled over and set back to 0 on duty bias,did a log and car is fine.thought setting at 0 or 50 is same?ill post up the both logs later when I get home.
Dude the same thing is happening to me after I changed my dusty from 0 to 50 in my 2010 335i. What gives Terry?
Reply With Quote
(#157)
Old
Payam @ BMS's Avatar
Payam @ BMS Payam @ BMS is offline
Super Moderator
 
Posts: 6,160
Join Date: Oct 2013
Car: e90 335i
Default 03-10-2020, 02:31 PM

Quote:
Originally Posted by Meka11113
Dude the same thing is happening to me after I changed my dusty from 0 to 50 in my 2010 335i. What gives Terry?
Post the log.


Burger Motorsports
Home of the Worlds fastest N20s, N54s, N55s, S55s, N63s, and S63s!

It is the sole responsibility of the purchaser and installer of any BMS part to employ the correct installation techniques required to ensure the proper operation of BMS parts, and BMS disclaims any and all liability for any part failure due to improper installation or use. It is the sole responsibility of the customer to verify that the use of their vehicle and items purchased comply with federal, state and local regulations. BMS claims no legal federal, state or local certification concerning pollution controlled motor vehicles or mandated emissions requirements. BMS products labeled for use only in competition racing vehicles may only be used on competition racing vehicles operated exclusively on a closed course in conjunction with a sanctioned racing event, in accordance with all federal and state laws, and may never be operated on public roads/highways. Please click here for more information on legal requirements related to use of BMS parts.
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 2 (1 members and 1 guests)
euro.step
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump




vBulletin Skin developed by: vBStyles.com
Copyright 2007 - 2020, N54tech.com