N54Tech.com - International Turbo Racing Discussion
Go Back   N54Tech.com - International Turbo Racing Discussion > Search Forums
Reload this Page Search Results
Showing results 1 to 25 of 27 Search: Posts Made By: glachhman
Forum: N54 04-28-2018, 05:25 PM
Replies: 202
Views: 25,871
Posted By glachhman
Flash only people, can we just remove out clutch...

Flash only people, can we just remove out clutch wire from the dme?
Forum: N54 11-09-2016, 08:10 PM
Replies: 11
Views: 2,711
Posted By glachhman
spec twin disk is expensive and a pain in the...

spec twin disk is expensive and a pain in the dick, just get 3+ or 5. I went through two before this one lasted.
Forum: N54 08-20-2016, 10:20 PM
Replies: 5
Views: 1,938
Posted By glachhman
I have an msport one for sale for 300

I have an msport one for sale for 300
Forum: N54 05-13-2016, 05:11 PM
Replies: 104
Views: 24,444
Posted By glachhman
Oops just saw the jb4 updates.

Oops just saw the jb4 updates.
Forum: N54 05-13-2016, 04:56 PM
Replies: 104
Views: 24,444
Posted By glachhman
Put in my sensor and changed the setting to 2 but...

Put in my sensor and changed the setting to 2 but getting a half engine light upon start up. If I clear codes it stays away, thoughts anyone?
Forum: N54 02-29-2016, 08:55 PM
Replies: 28
Views: 9,529
Posted By glachhman
harbor freight didnt work for me, its destroyed...

harbor freight didnt work for me, its destroyed the inside of the bearing and was left with the outer race. Ended up dremeling it slowly and carefully. I wouldnt mess with it.
Forum: N54 02-15-2016, 04:02 PM
Replies: 22
Views: 3,664
Posted By glachhman
You can code the dual zone button to work as rest...

You can code the dual zone button to work as rest but it only works below approximate 57 degrees so what will you do the rest of the year.
Forum: N54 02-06-2016, 09:08 PM
Replies: 49
Views: 9,236
Posted By glachhman
Is 335is tricky tuning just because of the dme?...

Is 335is tricky tuning just because of the dme? I'm running a 335is motor in my 07
Forum: N54 02-05-2016, 05:36 PM
Replies: 89
Views: 24,261
Posted By glachhman
Sorry meant more like ducts off the front bumper...

Sorry meant more like ducts off the front bumper for the cooling, or do you just have nothing attached?
Forum: N54 02-05-2016, 05:07 PM
Replies: 89
Views: 24,261
Posted By glachhman
which bumper shrouds you using?

which bumper shrouds you using?
Forum: N54 10-30-2015, 05:08 PM
Replies: 3,013
Views: 841,468
Posted By glachhman
Can someone post up their motiv900 settings for...

Can someone post up their motiv900 settings for jb4?
Forum: N54 10-21-2015, 07:09 PM
Replies: 3,013
Views: 841,468
Posted By glachhman
anyone know the right ff value for the new...

anyone know the right ff value for the new motiv900 kit? I think its a 14psi spring.
Forum: N54 09-21-2015, 04:07 PM
Replies: 9
Views: 2,000
Posted By glachhman
You can code this out in ncsexpert easily

You can code this out in ncsexpert easily
Forum: N54 08-31-2015, 06:17 AM
Replies: 165
Views: 57,138
Posted By glachhman
I got it figured out, I hadn't let the car sit...

I got it figured out, I hadn't let the car sit and idle after start up !
Forum: N54 08-25-2015, 05:15 PM
Replies: 165
Views: 57,138
Posted By glachhman
Any way to force evap readiness or change...

Any way to force evap readiness or change requirements for it to ready?
Forum: N54 08-22-2015, 12:33 PM
Replies: 6
Views: 2,037
Posted By glachhman
no one cares

no one cares
Forum: N54 07-25-2015, 11:43 AM
Replies: 27
Views: 9,019
Posted By glachhman
Works perfectly on my car

Works perfectly on my car
Forum: N54 07-22-2015, 11:25 AM
Replies: 27
Views: 9,019
Posted By glachhman
I want to run this but I can't figure out how to...

I want to run this but I can't figure out how to load the flash into tunerpro :(
Forum: N54 07-22-2014, 09:37 PM
Replies: 6
Views: 2,540
Posted By glachhman
Not sure of your location but I do it.

Not sure of your location but I do it.
Forum: DIY Modification 05-28-2014, 08:36 PM
Replies: 23
Views: 23,176
Posted By glachhman
Haha took the picture right before wash since the...

Haha took the picture right before wash since the dirty wheels made the brakes show more!
Forum: DIY Modification 05-24-2014, 09:10 PM
Replies: 23
Views: 23,176
Posted By glachhman
https://scontent-b-ord.xx.fbcdn.net/hphotos-xap1/t...

https://scontent-b-ord.xx.fbcdn.net/hphotos-xap1/t1.0-9/10410980_10202157525524778_6243378581554252303_n.jpg

Lime green here!
Don't flame me too hard!
Forum: N54 05-15-2014, 08:52 PM
Replies: 32
Views: 6,885
Posted By glachhman
TWOSTEPPPPPP ...

TWOSTEPPPPPP

https://scontent-a-iad.xx.fbcdn.net/hphotos-frc1/t1.0-9/1621915_10201470470628835_833451786_n.jpg
Forum: N54 04-14-2014, 07:55 PM
Replies: 13
Views: 4,837
Posted By glachhman
You arent the only one :( Luckily it only...

You arent the only one :(

Luckily it only pushed in the dme pins and a needle nose pliers pulled them right back out.
Forum: DIY Modification 03-02-2014, 07:49 PM
Replies: 712
Views: 198,468
Posted By glachhman
I'm so in for the next batch!

I'm so in for the next batch!
Forum: DIY Modification 02-16-2014, 10:59 AM
Replies: 712
Views: 198,468
Posted By glachhman
Golly I want a fully assembled but I wouldnt even...

Golly I want a fully assembled but I wouldnt even install it until springtime
Search took 0.01 seconds.

 
Forum Jump



vBulletin Skin developed by: vBStyles.com
Copyright 2007 - 2019, N54tech.com