N54Tech.com - International Turbo Racing Discussion
Go Back   N54Tech.com - International Turbo Racing Discussion > Search Forums
Reload this Page Search Results
Showing results 1 to 16 of 16 Search: Posts Made By: SteveSmokman
Forum: Market Place - For Sale / Trade / Wanted 02-20-2018, 08:03 PM
Replies: 0
Views: 741
Posted By SteveSmokman
WTB: Quad Diffuser for E92

Hey Everyone,

I've heard that ordering from Duke Dynamics is hit or miss, and I really need to find a quad diffuser with the same or very similar dimensions.

Does anyone know of a ebay replica...
Forum: General Tech Support, Tuning Advice, Logs, and Help Me Posts 02-09-2018, 10:59 AM
Replies: 4
Views: 944
Posted By SteveSmokman
So given my issue, would you recommend lowering...

So given my issue, would you recommend lowering or increasing my settings in 12?
Forum: General Tech Support, Tuning Advice, Logs, and Help Me Posts 02-08-2018, 11:39 PM
Replies: 4
Views: 944
Posted By SteveSmokman
I had to turn the setting for 11 down to about...

I had to turn the setting for 11 down to about 500 after doing the backend flash, because higher values caused really strange oscillation in boost at full throttle. I didn’t have this issue before...
Forum: General Tech Support, Tuning Advice, Logs, and Help Me Posts 02-08-2018, 10:55 AM
Replies: 4
Views: 944
Posted By SteveSmokman
Boost Spike and Hesitation on throttle snap

Hello,

I have been having what seems to be a strange issue with my 2011 335i (N55) with JB4 and MHD backend flash. Logs attached. This log was taken in map 1, but also happens in map 5.

When...
Forum: DIY Modification 01-28-2018, 11:11 PM
Replies: 2
Views: 1,541
Posted By SteveSmokman
Rotor change with wheel studs?

Hi everyone,

I just finished installing a wheel studs conversion kit, as I was sick of fighting to align the wheel perfectly and get a bolt in. Wheel spacers made this task very difficult.
...
Forum: Suspension and Brakes 01-27-2018, 10:15 AM
Replies: 0
Views: 1,712
Posted By SteveSmokman
Can I change rotors with wheel studs installed?

Hi everyone,

I just finished installing a wheel studs conversion kit, as I was sick of fighting to align the wheel perfectly and get a bolt in. Wheel spacers made this task very difficult.
...
Forum: General Tech Support, Tuning Advice, Logs, and Help Me Posts 09-24-2017, 09:23 PM
Replies: 6
Views: 949
Posted By SteveSmokman
Thanks Terry, I'll try to take a log tomorrow.

Thanks Terry, I'll try to take a log tomorrow.
Forum: General Tech Support, Tuning Advice, Logs, and Help Me Posts 09-24-2017, 08:55 PM
Replies: 6
Views: 949
Posted By SteveSmokman
It cranks over fine. I'm getting no codes through...

It cranks over fine. I'm getting no codes through the JB4. Im not sure how to tell if it's the hpfp or the lpfp.

I already dropped it at the shop since I didn't want to have to tow it twice if I...
Forum: General Tech Support, Tuning Advice, Logs, and Help Me Posts 09-24-2017, 07:52 PM
Replies: 6
Views: 949
Posted By SteveSmokman
That's what I'm sitting here thinking. Only thing...

That's what I'm sitting here thinking. Only thing that makes sense really. Is this a common failure? My car has 64k miles.
Forum: General Tech Support, Tuning Advice, Logs, and Help Me Posts 09-24-2017, 07:16 PM
Replies: 6
Views: 949
Posted By SteveSmokman
Stuck on the side of the road! Help!

I was out doing some highway driving, in map 5, everything seemed to be running fine. Then all of a sudden jb4 stops working completely. Couldn't access in dash menus. So I pulled over to restart the...
Forum: Market Place - For Sale / Trade / Wanted 09-22-2017, 07:27 PM
Replies: 0
Views: 786
Posted By SteveSmokman
F/S 18mm E series Wheel Spacers (BMS) Bay Area

Hi guys,

The 18mm wheel spacers cause my rear tires to rub going over bumps, so I need to downsize. These have been used for about 3 miles.

These are $120 shipped new, I'd like to get $90 if...
Forum: General Tech Support, Tuning Advice, Logs, and Help Me Posts 09-06-2017, 03:38 PM
Replies: 4
Views: 880
Posted By SteveSmokman
Do you get a reading in the "last safety" value?...

Do you get a reading in the "last safety" value? I get zero, but would think it would show overboost.
Forum: General Tech Support, Tuning Advice, Logs, and Help Me Posts 09-06-2017, 02:50 PM
Replies: 4
Views: 880
Posted By SteveSmokman
Kicked into Safety Map, not sure why

Hello,

I have been running in map 5 for a month now with no issues until this weekend. On harder pulls, I'm being kicked into safety map 4. The only log I was able to take (attached) is a short...
Forum: DIY Modification 08-30-2017, 09:49 AM
Replies: 3
Views: 5,283
Posted By SteveSmokman
Thanks!

Thanks for the info. I was able to take the intake into the hardware store and match the threads. I ended up using an M4x12. That was the closest length they had in stock, and it worked out fine.
Forum: General Tech Support, Tuning Advice, Logs, and Help Me Posts 08-18-2017, 10:01 PM
Replies: 1
Views: 1,083
Posted By SteveSmokman
BMS Intake - MAF Screws

I'm hoping someone can tell what screw type to use for the MAF sensor for E chassis N55 BMS intake.

I lost the screws during a swap out for smog check.

Anyone know the tread type and depth?...
Forum: DIY Modification 08-18-2017, 08:43 PM
Replies: 3
Views: 5,283
Posted By SteveSmokman
Bump!

I need to know this as well!
Search took 0.00 seconds.

 
Forum Jump



vBulletin Skin developed by: vBStyles.com
Copyright 2007 - 2020, N54tech.com