N54Tech.com - International Turbo Racing Discussion
Go Back   N54Tech.com - International Turbo Racing Discussion > Search Forums
Reload this Page Search Results
Showing results 1 to 10 of 10 Search: Posts Made By: greg_e
Forum: N54 09-18-2020, 10:08 AM
Replies: 4
Views: 659
Posted By greg_e
You can’t add more material to the head to...

You can’t add more material to the head to increase compression. CR is mainly done through the pistons. I recently built my motor with 9.5:1 CP pistons and CP rods for high boost, corrections through...
Forum: N54 04-18-2020, 10:55 AM
Replies: 2
Views: 585
Posted By greg_e
Iíve noticed that too for a while now Iím not...

Iíve noticed that too for a while now Iím not sure if itís an issue of newer or older maps bc I never had updated or reflashed the map but I sure do miss the gunshots
Forum: Support & Log Review 12-26-2019, 11:24 AM
Replies: 2
Views: 405
Posted By greg_e
I did check that and there was no moisture in...

I did check that and there was no moisture in there or under the DME connectors. Also if it matters I went from the jb4 g4 to g5 board a couple days ago and installed 2 step and anti lag. Anti lag...
Forum: Support & Log Review 12-26-2019, 10:21 AM
Replies: 2
Views: 405
Posted By greg_e
Limp mode and bouncy idle left me on the side of the freeway please help!

Hey guys so I have a 07 335i I was on my way to work this morning and it was raining pretty hard if that matters, car all of sudden lost all power and went into limp mode. Got the half CEL message...
Forum: Market Place - For Sale / Trade / Wanted 12-25-2019, 12:34 AM
Replies: 4
Views: 441
Posted By greg_e
I have a Jb4 board available but without...

I have a Jb4 board available but without Bluetooth or the harness if that interests you
Forum: Support & Log Review 12-14-2019, 08:44 AM
Replies: 7
Views: 340
Posted By greg_e
I’m in California would I be able to just buy the...

I’m in California would I be able to just buy the replacement board or do I need a whole new kit?
And would I need to buy anti lag and 2step again? No right?
Forum: Support & Log Review 12-13-2019, 09:31 PM
Replies: 7
Views: 340
Posted By greg_e
I inputted 4 for the DME version I have, what...

I inputted 4 for the DME version I have, what should I put in?
Also can I use the g5 firmware on my g4 board? I might be blind but I canít find the latest g4 version
Forum: Support & Log Review 12-13-2019, 08:21 PM
Replies: 7
Views: 340
Posted By greg_e
The misfire is intermittent, itís not missing...

The misfire is intermittent, itís not missing right now
I enabled 6 cyl timing hereís the updated log with similar conditions
I was pretty I was running lean but thank you for confirming that!
I...
Forum: Support & Log Review 12-13-2019, 01:13 PM
Replies: 7
Views: 340
Posted By greg_e
Log check please, acting weird

Car was running fine a couple days ago, all of a sudden i started having a cylinder 4 misfire and car is now boosting at 15psi, previously it was at 20-21. I donít think I have a boost leak but...
Forum: N54 12-13-2019, 01:07 PM
Replies: 3
Views: 868
Posted By greg_e
Did you check the mosfets in the DME? Possibly...

Did you check the mosfets in the DME? Possibly could’ve fried them, they weren’t designed to control spark at 10k rpm lol
Search took 0.00 seconds.

 
Forum Jump



vBulletin Skin developed by: vBStyles.com
Copyright © 2007 - 2020, N54tech.com