N54Tech.com - International Turbo Racing Discussion
Go Back   N54Tech.com - International Turbo Racing Discussion > Search Forums
Reload this Page Search Results
Showing results 1 to 25 of 100 Search: Posts Made By: iminhell1
Forum: N54 09-06-2021, 04:56 PM
Replies: 346
Views: 109,672
Posted By iminhell1
I'm not smart. But I'm really curious as to the...

I'm not smart. But I'm really curious as to the total heating gain through all the parts?
If there is a 8* gain from the LPFP to the HPFP, then a gain in the pump, then a gain to the rail, then a...
Forum: N54 09-06-2021, 04:51 PM
Replies: 346
Views: 109,672
Posted By iminhell1
Also, Factory fuel line from tank to HPFP:

Also,
Factory fuel line from tank to HPFP:
Forum: N54 09-06-2021, 04:48 PM
Replies: 346
Views: 109,672
Posted By iminhell1
Viscosity table --> Pressure Drop...

Viscosity table --> Pressure Drop (https://www.gates.com/us/en/knowledge-center/engineering-applications/pressure-drop.html)

Calculator used --> Fluid Flow Calculator...
Forum: N54 09-06-2021, 04:44 PM
Replies: 346
Views: 109,672
Posted By iminhell1
Now with the rail outlets to injectors drilled...

Now with the rail outlets to injectors drilled with a 9/64" bit:
Forum: N54 09-06-2021, 04:43 PM
Replies: 346
Views: 109,672
Posted By iminhell1
Halloween just around the corner and it brings...

Halloween just around the corner and it brings things back from the dead ...


So just because I wanted to know:
Forum: N54 09-29-2020, 04:46 PM
Replies: 10
Views: 1,629
Posted By iminhell1
Since spoon feeding is required for you, The...

Since spoon feeding is required for you,

The SECRET To Replacing Index 12 Injectors FOR CHEAP on BMW N54 (135i, 335i, 535i) - YouTube (https://youtu.be/i69WZEd0yJA?t=172)


and I guess looking...
Forum: N54 09-28-2020, 05:30 PM
Replies: 10
Views: 1,629
Posted By iminhell1
Jake spent too much on tools and ****. This...

Jake spent too much on tools and ****.

This is the most cost effective injector tool --> PRECISION RACEWORKS - BMW N54 INJECTOR TOOL #601-0005...
Forum: N54 09-28-2020, 03:57 AM
Replies: 3
Views: 1,562
Posted By iminhell1
95% of the time it's a vacuum leak. ...

95% of the time it's a vacuum leak.
Check/replace all the hoses coming off the vacuum pump. Make sure the large hose on the vacuum pump is secure. Make sure the cover isn't cracked (more a problem...
Forum: N54 09-25-2020, 06:08 PM
Replies: 10
Views: 1,629
Posted By iminhell1
To do them right, look for a large brown...

To do them right, look for a large brown container, top should flip open. Toss injectors in and buy a real set that aren't fakes.

Want to know a dead giveaway that they are fake?
Look at the...
Forum: N54 09-11-2020, 10:04 AM
Replies: 6
Views: 1,141
Posted By iminhell1
90% isn't unheard of. Around me we'll usually...

90% isn't unheard of.
Around me we'll usually run 80-90% all Summer. Come Winter it'll drop to about 72% and hold there.
Forum: Support & Log Review 08-12-2020, 03:56 PM
Replies: 4
Views: 918
Posted By iminhell1
tq tables and airflow model, look into them

tq tables and airflow model, look into them
Forum: N54 08-06-2020, 07:12 PM
Replies: 2
Views: 923
Posted By iminhell1
Message Seth. He should have some in the shop. ...

Message Seth. He should have some in the shop.

And yes. It's an anaerobic sealant and like any sealant, it fills in the little gaps that could be left by machining.
Forum: N54 07-21-2020, 03:16 PM
Replies: 1
Views: 936
Posted By iminhell1
Black would be lots of unburnt fuel. Could be...

Black would be lots of unburnt fuel.
Could be stuck injector dumping fuel in. Unplug them one by one and see if you can get clean exhaust once.

But first I'd do a compression test. If you get one...
Forum: N54 07-19-2020, 12:18 PM
Replies: 2
Views: 1,064
Posted By iminhell1
It's spam verbatim of a reddit post 2 years old.

It's spam
verbatim of a reddit post 2 years old.
Forum: N54 07-17-2020, 09:48 AM
Replies: 12
Views: 1,919
Posted By iminhell1
So what car is this going in, (what do I...

So what car is this going in,

(what do I have to watch out for)
Forum: N54 07-13-2020, 04:28 PM
Replies: 9
Views: 1,467
Posted By iminhell1
And lets back up a step here once. How much...

And lets back up a step here once.

How much pressure are you putting into the system?
Where you're describing is right near the seam for the PCV stuff in the valvecover. If you didn't...
Forum: N54 07-11-2020, 09:37 AM
Replies: 8
Views: 1,906
Posted By iminhell1
Look at a tap. How is it going to block the...

Look at a tap.
How is it going to block the hole?

Your mechanic is a moron.
Forum: N54 06-24-2020, 06:35 PM
Replies: 0
Views: 884
Posted By iminhell1
Fuel pump hanger sale

Terry@bms, how long does this sale run?
Forum: N54 05-05-2020, 10:01 AM
Replies: 10
Views: 1,236
Posted By iminhell1
I wouldn't call anything damaged. More worn. ...

I wouldn't call anything damaged. More worn.
The innerds are designed to 'flex' a little. Age and power can take some of the spring out of it IMO. Add to that worn thrust bearing on the crankshaft...
Forum: N54 05-04-2020, 06:33 AM
Replies: 10
Views: 1,236
Posted By iminhell1
the converter will move back an forth a little as...

the converter will move back an forth a little as pressure to it changes ... that little bit it had to pull forward to touch the flexplate, it can move that much, 1/8" or so. that may be enough?
Forum: N54 05-03-2020, 09:06 PM
Replies: 10
Views: 1,236
Posted By iminhell1
flexplate is bent then. can try to heat and...

flexplate is bent then.
can try to heat and hammer it back a bit, or just bite the bullet and buy a new one.
Forum: N54 04-30-2020, 08:57 PM
Replies: 10
Views: 1,236
Posted By iminhell1
It is possible a bolt backed out. Pull the...

It is possible a bolt backed out.
Pull the inspection plug on the bottom of the trans and wiggle a magnet around as see if you catch something.

Weather you TQ them to spec or not, a dab of thread...
Forum: N54 04-18-2020, 09:04 AM
Replies: 3
Views: 1,392
Posted By iminhell1
That would be the bedplate/girdle what ever you...

That would be the bedplate/girdle what ever you wish to call it. The gasket there is injected. It's not something you really want tot try and fix yourself. To do so you need to remove the oil pan and...
Forum: N54 03-10-2020, 09:13 AM
Replies: 5
Views: 2,027
Posted By iminhell1
Cost of repair now vs cost of not. Pretty easy to...

Cost of repair now vs cost of not. Pretty easy to fix it now vs having to find a new block because you didn't.
Forum: N54 03-09-2020, 11:54 AM
Replies: 13
Views: 1,986
Posted By iminhell1
You can't trim the alignment nubs off. That's...

You can't trim the alignment nubs off. That's what the C clip uses to hold the inlet on the intercooler. Shave that smooth (so it can rotate) and it'll just blow out soon as you hit boost.



Per...
Search took 0.01 seconds.

 
Forum Jump



vBulletin Skin developed by: vBStyles.com
Copyright 2007 - 2020, N54tech.com