N54Tech.com - International Turbo Racing Discussion
Go Back   N54Tech.com - International Turbo Racing Discussion > Search Forums
Reload this Page Search Results
Showing results 1 to 25 of 100 Search: Posts Made By: MasterYous
Forum: Support & Log Review Yesterday, 07:45 AM
Replies: 26
Views: 290
Posted By MasterYous
Are you sure you went the wrong way? Higher bias...

Are you sure you went the wrong way? Higher bias settings raise overall PID value and are equivalent to raising FF (except FF is global and bias is per RPM). Im thinking we want to lower FF since I...
Forum: Support & Log Review 03-22-2019, 05:11 PM
Replies: 26
Views: 290
Posted By MasterYous
No need to thank me for my patience, lol. I'm...

No need to thank me for my patience, lol. I'm happy to keep going, this is fun. It should be me who is thanking you!

Logs with bias settings as suggested. No other changes.

What can I say?...
Forum: B58, B48 03-21-2019, 04:28 PM
Replies: 11
Views: 116
Posted By MasterYous
Please just dig around on the b58 forum. There...

Please just dig around on the b58 forum. There are varying levels of opinion on the EWG connector.
Forum: B58, B48 03-21-2019, 03:59 PM
Replies: 11
Views: 116
Posted By MasterYous
I looked at your first log and don't see...

I looked at your first log and don't see overboost. In fact, your boost is a little low for Map 3, but the log is pretty clean.
Forum: Support & Log Review 03-21-2019, 03:55 PM
Replies: 2
Views: 44
Posted By MasterYous
Not bad. You're pulling timing in early part of...

Not bad. You're pulling timing in early part of the run, though, and trims are high in places.

Better logs would be from 2.5k to redline, starting in 3rd.

Can you be more specific about your...
Forum: B58, B48 03-21-2019, 03:40 PM
Replies: 11
Views: 116
Posted By MasterYous
That doesn’t sound like a “true” drivetrain...

That doesn’t sound like a “true” drivetrain error, and yes there is an EWG connector for the B58; I run one and so does almost everyone else using meth.

Look around, most drivetrain errors occur...
Forum: B58, B48 03-21-2019, 02:51 PM
Replies: 11
Views: 116
Posted By MasterYous
Flash your DME with an appropriate map. I don’t...

Flash your DME with an appropriate map. I don’t see how you’re going to avoid stuff like this since a JB4 can’t override o2 sensor programming. You can also ask BMS if the forthcoming B58 BEF will...
Forum: Support & Log Review 03-21-2019, 11:28 AM
Replies: 26
Views: 290
Posted By MasterYous
More logs, this time with duty bias at 0. So...

More logs, this time with duty bias at 0. So now, we have meth safety at 26, all duty bias settings at 0, and 50/50 WMI. (FOL still 10)

You might find it interesting that FF has learned all the...
Forum: Support & Log Review 03-19-2019, 09:26 PM
Replies: 26
Views: 290
Posted By MasterYous
My understanding from an old post by Terry (see...

My understanding from an old post by Terry (see my first post in this thread for the link) is that Duty Bias of 50 is same as 0 which I think is off, yes. Mathematically it would make sense given his...
Forum: Support & Log Review 03-19-2019, 07:17 PM
Replies: 26
Views: 290
Posted By MasterYous
Here's a log from today after returning duty bias...

Here's a log from today after returning duty bias to defaults and raising boost safety back to 26. I waited until later in the day to log, to allow for some more learning - but today was not a good...
Forum: Support & Log Review 03-18-2019, 05:07 PM
Replies: 26
Views: 290
Posted By MasterYous
3 logs attached at WMI 50/50. Did not reset duty...

3 logs attached at WMI 50/50. Did not reset duty bias to default, that will be next. Did many pulls yesterday (unlogged) to JB4-learn a bit.

One thing that is obvious in a side-by-side: trims...
Forum: B58, B48 03-18-2019, 11:52 AM
Replies: 7
Views: 297
Posted By MasterYous
Late to the party. My M240i is a 6MT and no...

Late to the party. My M240i is a 6MT and no clutch issues.

None of our responses mean much however, without shared context. I am not racing the JB4. I don't launch at 5k rpm at 16 psi...
Forum: Support & Log Review 03-18-2019, 11:47 AM
Replies: 26
Views: 290
Posted By MasterYous
I'd be happy even at a consistent 19psi with...

I'd be happy even at a consistent 19psi with proper timing, so 20 is perfectly adequate for now. ;) I've read the posts about what Terry put down on the dyno with a 340 and meth back in the day.
...
Forum: Support & Log Review 03-17-2019, 07:36 AM
Replies: 26
Views: 290
Posted By MasterYous
Thanks much again. :) I had come to a...

Thanks much again. :)

I had come to a similar conclusion about the meth mixture. With the tank running low, flow was reduced to about 60-80 and I noticed much smoother pulling.

So I’ll switch...
Forum: Support & Log Review 03-15-2019, 02:06 PM
Replies: 26
Views: 290
Posted By MasterYous
And another short log from this morning (3/15)...

And another short log from this morning (3/15) after the car had warmed up. No changes to settings at all, and yet the wobbling is more evident this morning than it was in the afternoon. Just...
Forum: Support & Log Review 03-14-2019, 03:31 PM
Replies: 26
Views: 290
Posted By MasterYous
Two more logs from this afternoon, after a lot of...

Two more logs from this afternoon, after a lot of FF learning. The car is starting to feel a little better. Same settings as JBoe recommendation. Throttle plate not clean yet but saw some advance...
Forum: Support & Log Review 03-14-2019, 07:44 AM
Replies: 26
Views: 290
Posted By MasterYous
Wow, that is really excellent analysis. Much...

Wow, that is really excellent analysis. Much appreciated. I have been trying to get that throttle under control since "Day One" of when I went to WMI. It has always been my goal, but I haven't...
Forum: Support & Log Review 03-13-2019, 11:04 AM
Replies: 26
Views: 290
Posted By MasterYous
I really appreciate the help here, I'd like to...

I really appreciate the help here, I'd like to start with that. :)

My car just really does not like these settings. DME BT wobbling is back with these settings. I spent some time doing runs and...
Forum: Support & Log Review 03-12-2019, 10:35 AM
Replies: 26
Views: 290
Posted By MasterYous
I agree with your general analysis about timing...

I agree with your general analysis about timing and think the result could be much more impressive with better timing, yes. I tried your settings (exactly as you mentioned them) and the JB4 crashed...
Forum: Support & Log Review 03-11-2019, 05:15 AM
Replies: 26
Views: 290
Posted By MasterYous
M240 - Dialing in meth - progress made

I posted yesterday that after months of off and on tinkering, I've managed to find settings that allow me to run Map 7 that avoids the DME BT wobble which causes hesitation during acceleration at...
Forum: B58, B48 03-11-2019, 04:56 AM
Replies: 5
Views: 252
Posted By MasterYous
You have good eyes, yes it is kinked ever so...

You have good eyes, yes it is kinked ever so slightly. I’ve tested with purge multiple times and the flow seems ok. I’ll PM you a separate thread to continue the discussion. :)
Forum: Support & Log Review 03-10-2019, 09:29 PM
Replies: 2
Views: 157
Posted By MasterYous
It’s hard to understand what you’re saying. The...

It’s hard to understand what you’re saying. The first rule around here is to post a log with long runs from 3k-redline.

Are you running the BMS WMI kit? Map 7 is for meth. Uncheck all the...
Forum: Support & Log Review 03-10-2019, 09:23 PM
Replies: 10
Views: 255
Posted By MasterYous
I agree. 428-445whp from 17psi? Goodness. Your...

I agree. 428-445whp from 17psi? Goodness. Your mods are nice but you hit this kinda hp with no meth? I need to get to a dyno. I’m at 18-19 psi routinely using WMI.
Forum: Support & Log Review 03-10-2019, 09:07 PM
Replies: 4
Views: 88
Posted By MasterYous
This car does that. Your DME BT is wobbling just...

This car does that. Your DME BT is wobbling just a bit but not too badly. If the car feels good and you’re not feeling hesitation or the boost spikes then keep going. Otherwise you might have to...
Forum: Support & Log Review 03-10-2019, 03:09 PM
Replies: 8
Views: 175
Posted By MasterYous
I finally did it. I finally dialed in this SOB...

I finally did it. I finally dialed in this SOB motor on meth/map7 with additive 40! Thanks to some suggestions from JBoe and dRdiesel as well as Terry's extremely informative post here:
JB4 Duty...
Search took 0.02 seconds.

 
Forum Jump



vBulletin Skin developed by: vBStyles.com
Copyright 2007 - 2018, N54tech.com