N54Tech.com - International Turbo Racing Discussion
Go Back   N54Tech.com - International Turbo Racing Discussion > Search Forums
Reload this Page Search Results
Showing results 1 to 25 of 51 Search: Posts Made By: Stroker396
Forum: Support & Log Review 10-26-2020, 02:15 PM
Replies: 5
Views: 108
Posted By Stroker396
Ok well i had replaced 1 of the 2 boost solenoids...

Ok well i had replaced 1 of the 2 boost solenoids that i knew was dead. It was just a matter of time til i replaced the other. It is ordered. I will check the connection at the front turbo again...
Forum: Support & Log Review 10-24-2020, 11:16 AM
Replies: 5
Views: 108
Posted By Stroker396
So the duty bias setting were set at the default...

So the duty bias setting were set at the default for hybrid turbos. You dont think they might need adjustment?
Forum: Support & Log Review 10-24-2020, 10:02 AM
Replies: 5
Views: 108
Posted By Stroker396
Because boost is below target by more than 2psi?

Because boost is below target by more than 2psi?
Forum: Support & Log Review 10-24-2020, 09:38 AM
Replies: 5
Views: 108
Posted By Stroker396
Runs pretty good, room for more?

So after double checking the 2 step wiring and realizing it wasn't correct, I fixed it and the 2 step is still not working. Frustrating.

Attached are runs in map 2, map 5 and map 5 with E30
...
Forum: N54 10-19-2020, 06:42 PM
Replies: 8
Views: 1,177
Posted By Stroker396
So far works great. Question is there any chance...

So far works great. Question is there any chance of a tab to setup larger gauges that we can select and monitor in real time similar to the mobile app?

or maybe have the graph show in real time.
Forum: Market Place - For Sale / Trade / Wanted 10-19-2020, 11:13 AM
Replies: 5
Views: 421
Posted By Stroker396
No it has never been resurfaced. I bought it...

No it has never been resurfaced. I bought it new, installed it, realized it was not sufficient to hold all the power i added and replaced it.

Yes I would sell it seprately. 350 shipped
I wont...
Forum: N54 10-04-2020, 07:40 AM
Replies: 2
Views: 656
Posted By Stroker396
Thats a pretty impressive level. PI will be...

Thats a pretty impressive level. PI will be coming eventually.

I did some reading and looks like with the JB4 the only way to monitor for knock is to look in the logs for instant 3degree timing...
Forum: Market Place - For Sale / Trade / Wanted 10-03-2020, 01:53 PM
Replies: 5
Views: 421
Posted By Stroker396
I did not see a big difference from stock It was...

I did not see a big difference from stock It was a nice setup, smooth engagement. It continued to drive like normal I just had to keep the car out of building high boost so I would shift by 4k rpm....
Forum: N54 09-30-2020, 10:08 AM
Replies: 24
Views: 1,253
Posted By Stroker396
Bug? What bug....bought this car a yr ago bone...

Bug? What bug....bought this car a yr ago bone stock.

Everything you need is in the stickies. Go to the log support section ( top of page) for more detailed info on the parameter meaning of the...
Forum: N54 09-29-2020, 07:27 PM
Replies: 2
Views: 656
Posted By Stroker396
How much Max PSI on 93?

So E85 is less prone to knock (higher octane) which allows you to increase the level of boost correct. The downside is that it requires 30% more volume hence the need for better lpfp, pi etc...
...
Forum: Support & Log Review 09-13-2020, 06:58 PM
Replies: 9
Views: 287
Posted By Stroker396
So as fast as I fixed it I broke it. It peaked...

So as fast as I fixed it I broke it. It peaked at 17.2psi on map 2. I went out and did 2 tests runs from a dig (drag race) on the second run it bogged hard since no 2 step so no boost. and it...
Forum: Support & Log Review 09-13-2020, 08:31 AM
Replies: 9
Views: 287
Posted By Stroker396
Ok so I was doing a lot of reading and sure...

Ok so I was doing a lot of reading and sure enough it was a big boost leak.

Unfortunately the 2 Step still does not work though.
Forum: Support & Log Review 09-12-2020, 03:32 PM
Replies: 9
Views: 287
Posted By Stroker396
So installed a new G5 board today and no change. ...

So installed a new G5 board today and no change. In fact I am pretty sure after looking at it that the old board was also a G5. Tried it with both firmware versions 14 and 15. Still no change.
...
Forum: Support & Log Review 09-05-2020, 08:42 AM
Replies: 9
Views: 287
Posted By Stroker396
basically the same thing. also the 2 step...

basically the same thing.

also the 2 step has never worked. is it maybe because it might be a G4 board
Forum: Support & Log Review 09-01-2020, 02:19 PM
Replies: 9
Views: 287
Posted By Stroker396
It was in map 1 when i started Yes it is 4/2

It was in map 1 when i started

Yes it is 4/2
Forum: Support & Log Review 09-01-2020, 10:12 AM
Replies: 9
Views: 287
Posted By Stroker396
Not boosting to target???

Ok so I started getting a little bit of boost. I went back and checked on the settings and it seemed a few were off so I fixed them for hybrid turbos. I did a quick run to see if anything has been...
Forum: N54 07-06-2020, 10:45 AM
Replies: 68
Views: 9,176
Posted By Stroker396
Looking forward to the updates. Installed a...

Looking forward to the updates. Installed a Walbro 525 and having issues.
Forum: N54 06-30-2020, 11:01 AM
Replies: 1
Views: 403
Posted By Stroker396
Would it be correct to assume that since the DME...

Would it be correct to assume that since the DME is not getting a LPFP reading that could be why it is not boosting?

LOg attached
Forum: N54 06-30-2020, 10:23 AM
Replies: 1
Views: 403
Posted By Stroker396
Fuel pump and Map 8???

So I installed the Walbro 525 and I get an intermittent fuel pump code. It almost seems like a loose wire as it was on most of the time and occasionally went off for a little bit. I have cleaned...
Forum: Support & Log Review 06-27-2020, 05:51 AM
Replies: 43
Views: 5,970
Posted By Stroker396
Old thread but current issue. I did not see any...

Old thread but current issue. I did not see any solution (other than tune it out) i installed the Walbro 525 and it works but does not send the reading to the DME. I think i need to fix that first.
Forum: Market Place - For Sale / Trade / Wanted 06-21-2020, 04:57 PM
Replies: 0
Views: 296
Posted By Stroker396
2008 BMW 535i Twin Turbo Set N54 OEM

2008 BMW 535i Twin Turbo Set N54 OEM. Condition is Used. This also fits the 135i and Z4 with the N54 engine. This does not include 1 of the wategate actuators or any of the oil and coolant lines. ...
Forum: Market Place - For Sale / Trade / Wanted 06-21-2020, 04:54 PM
Replies: 5
Views: 421
Posted By Stroker396
SMFW and clutch

$520 Shipped

This is a Turner Motorsports single mass flywheel and a stock F10 550i Clutch rated for 440ft lbs. It has about 2000 miles (1000 highway) It has 8 bolts for the crankshaft.

I had...
Forum: Kia & Hyundai Turbo 04-26-2020, 08:32 PM
Replies: 0
Views: 709
Posted By Stroker396
Genesis 2.0T surging at idle. not holding boost. log included

So my friends car is having an issue and until we solve it the JB4 is of no use.

Initially he had a check engine light and we were able to resolve it by replacing the BOV solenoid which was bad.
...
Forum: Market Place - For Sale / Trade / Wanted 03-15-2020, 11:59 AM
Replies: 1
Views: 869
Posted By Stroker396
Here are a few pictures I have more. Tony...

Here are a few pictures I have more.

Tony confirmed these are 3.5 years old and the previous owner put 10k miles on them.
Forum: Market Place - For Sale / Trade / Wanted 03-15-2020, 08:04 AM
Replies: 1
Views: 1,132
Posted By Stroker396
Just posted vvt stg2

Just posted vvt stg2
Search took 0.01 seconds.

 
Forum Jump



vBulletin Skin developed by: vBStyles.com
Copyright 2007 - 2020, N54tech.com