N54Tech.com - Your Source for International Turbo BMW Racing Discussion
(#1)
Old
Terry @ BMS's Avatar
Terry @ BMS Terry @ BMS is online now
Tuner
 
Posts: 21,783
Join Date: Jan 2008
Default F Series N55 JB4 - 02-06-2013, 07:11 PM

Use subject to terms and conditions posted at http://www.burgertuning.com/terms.html

THIS PART IS LEGAL FOR USE ONLY IN COMPETITION RACING VEHICLES AS DEFINED UNDER CALIFORNIA LAW, AND IS NOT LEGAL FOR USE IN ANY OTHER MOTOR VEHICLE. California law defines a "racing vehicle" as "a competition vehicle not used on public highways." (Calif. Health & Safety Code 39048) This part may only be used on competition racing vehicles operated exclusively on a closed course in conjunction with a sanctioned racing event. Competition-only motor vehicles may not be driven to a racing event on a public highway and must be transported on a trailer or other carrier. USE OF THIS PART IN ANY OTHER VEHICLE MAY SUBJECT YOU TO FINES AND PENALTIES FOR VIOLATION OF FEDERAL AND/OR STATE LAW, WILL VOID YOUR WARRANTY FROM BURGER MOTORSPORTS, INC, AND CAN VOID YOUR VEHICLE'S WARRANTY. It is your responsibility to comply with all applicable federal and state laws relating to use of this part, and Burger Motorsports, Inc hereby disclaims any liability resulting from the failure to use this part in compliance with all applicable federal and state laws.

When working with live wires ALWAYS disconnect the negative battery terminal in the trunk first. Do not attempt to install the tuner, connect the tuner box to the harness, or otherwise work on the vehicles electrical system with the battery connected. Doing this may result in a damaging voltage spike being sent to the DME.

Also be very careful when working with the BMS USB cable as it sits close to the battery rail which is a live +12v connection. Allowing the USB cable to touch the +12v connection WILL damage the JB4 and MAY damage the TMAP sensor wiring requiring the ground bypass at the bottom of the guide to be performed. Wrapping a piece of cloth tape over the battery rail connection and/or USB connection will help prevent accidental damage.


Current F Series JB4 Install Guide

Hey guys,

This thread will be used to centralize all F series JB4 information. Anything important is in the first post. The rest is 100 pages of discussion, much of which may no longer be relevant. If its not in the first post then its probably not very important.

Note: We sell two systems for the F series N55. The Stage1 and the JB4. There is no such thing as a JB4 Stage1 and no such thing as a JB4 Stage2. The Stage1 DOES NOT have updatable firmware, CANbus, or changeable maps. If you have a Stage1 system then none of the information in this post is relevant to you.

To order a new F series JB4 kit: http://burgertuning.com/N55_JB4_F_ch...BMW_tuner.html

To avoid cluttering up the thread any support requests will be deleted from this thread without being read. If you require assistance email tech support at jon@burgertuning.com.

JB4 Interface: Latest JB4 Interface Download. When updating your interface you may need to first go to "add remove programs" and "remove" your previous JB4 interface.

If you need directions on how to connect a laptop to your JB4 to update firmware, datalog, or change maps via the laptop interface Click here.

Map Info (selected via menu 0 in dash or using JB4 Mobile/laptop interface. Map1 is the default map)

Map 0: JB4 disabled
Map 1: Additive target, around 4psi over stock.
Map 2: Additive target, around 6psi over stock. Suggested for those with 93 octane and bolt on modifications. Also good for small E85 mixtures.
Map 3: Progressive WMI mapping.
Map 4: Stock performance with JB4 active for logging only.
Map 5: Autotuning map, absolute target of 11-17psi based on octane and conditions.
Map 6: User definable absolute target map. Suggested for troubleshooting by professionals only.
Map 7: Race gas map. Absolute target of 18.5psi. Requires straight unleaded race gas.

E85 Use

Up to 30% E85 mixtures can be used in most situations.

Firmware

Both the F10 and F30 N55 motors share the same firmware. Note models using the pneumatic wastegate, primarily 2013-early 2014 models where the JB4 harness blue patch is connected, need to use PWG firmware. Those equipped with an electronic wastegate, primarily 2014+ models where the JB4 blue batch is NOT used, need to use EWG firmware. Note for older systems POSITAP firmware (the old wire taps for brown/green wires) has been discontinued and no new updates will be done. So upgrade to the OBDII CANbus connector & firmware if you wish to run the latest firmware & features.

535 Differences

1) To enable the BC button menu changes on F10/535 models you must connect to the JB4 using a BMS DATA cable and change the "Future Use D" setting to 2 and press save. Then turn off ignition and lock doors for 5 min to allow the DME to reset.


************************************************** ************************
*Special Settings For F Series JB4 EWG & PWG version 11+
************************************************** ************************


FUD:
bit0 - Disable in dash BC button controls
bit1 - Alternative in dash BC F10 compatibility mode
bit2 - Disable oil temp warmup protection -- full boost target when oil temps < 160
bit3 - Disable wastegate/FF adaption learning for diagnostic purposes
bit4 - Enable user adjustable progressive meth control
bit5 - Disable port injection mapping tip in gain
bit6 - Enable extra timing cylinder logging
bit7 - Slow down CANbus sample rate - required for some vehicles with older software

FutureUseA: Negative offset to dutycycle via EWG connector to correct for over boost conditions when PWM is low

Map6: Values of less than 10psi under boost 1500rpm will cause map6 to act as an additive rather than absolute map


Firmware notes:

N55_FSERIES_OBDII_EWG_12:

1) Adjustment for those running high boost back end flash maps.

N55_FSERIES_OBDII_EWG_11:

1) Revised FUD settings to bit logic allowing multiple selections. Settings are as above. Note revised FUD bit options are for v11 and higher firmware ONLY.
2) Changes to partial throttle mapping to improve smoothness.
3) By default cyl1 and cyl5 only are logged to speed up sample rate. Other cylinders are loggable via a FUD bit 6.
4) Various other minor changes.
5) Various changes to PI mapping and other test features under development.

N55_FSERIES_OBDII_PWG_11:

1) Minor changes to bring PWG firmware up to current EWG firmware specifications.


EWG Control

For those with 2014+ models with the new electronic wastegate this thread has addl information on optional EWG control for higher boost maps.


OBDII Firmware Wheel Controls and Map Switching In Dash:



In dash options

Note CANflap and menu system for changing maps, enabling the boost gauge, etc, now use exclusively the BC button.

'***************************************
Exhaust Valve Mode:
'***************************************

Toggle between flap open, flap closed, and OEM operation, by pressing the button for 2 seconds and letting go. The left blinker will flash for valve open, right blinker for valve closed, and both blinkers for OEM operation. The valve setting is persistent and will remain in effect until you change it. If you hold the button too long you'll jump in to the in dash menu system below.

'***************************************
'OBDII In Dash Menu
'***************************************

'0 map menu, map shown on tach. Note map guide above.
'1 Not used for this model
'2 Boost gauge on fuel, boost is shown in the fuel gauge under heavy throttle with empty being 0psi boost and full being whatever you've assigned to your boost failsafe PSI on the user adjustment page. Default is 18psi. (OFF tach = 0, ON tach = 1000)
'3 LED MAX brightness mode. For those with factory LED headlights this option brightens HALO during nighttime operation. (OFF tach = 0, ON tach = 1000)
'4 Delete Fault Codes.
'5 1st gear boost limit setting. 0-7000rpm = 0-20psi.
'6 2nd gear boost limiter
'7 3rd gear boost limiter

F Series N55 Default Settings:

Name:  n55_defaults.jpg
Views: 10759
Size:  73.6 KB


Copyright Notice:
JB4 Software is Copyright 2006-2016 by Burger Motorsports Incorporated. All rights are reserved. De-compilation, disassembly, reverse-engineering, alteration, and redistribution in any form without the prior written consent of Burger Motorsports Inc. is prohibited.
Attached Files
File Type: hex N55_FSERIES_OBDII_PWG_11_T1.hex (75.4 KB, 971 views)
File Type: hex N55_FSERIES_OBDII_EWG_12_T5.hex (78.5 KB, 203 views)


Burger Motorsports
Home of the Worlds fastest N20s, N54s, N55s, S55s, N63s, and S63s!

It is the sole responsibility of the purchaser and installer of any BMS part to employ the correct installation techniques required to ensure the proper operation of BMS parts, and BMS disclaims any and all liability for any part failure due to improper installation or use. It is the sole responsibility of the customer to verify that the use of their vehicle and items purchased comply with federal, state and local regulations. BMS claims no legal federal, state or local certification concerning pollution controlled motor vehicles or mandated emissions requirements. BMS products labeled for use only in competition racing vehicles may only be used on competition racing vehicles operated exclusively on a closed course in conjunction with a sanctioned racing event, in accordance with all federal and state laws, and may never be operated on public roads/highways. Please click here for more information on legal requirements related to use of BMS parts.

Last edited by Steve @ BMS/Fuel-It!; 05-25-2016 at 08:10 AM..
Reply With Quote
(#2)
Old
Terry @ BMS's Avatar
Terry @ BMS Terry @ BMS is online now
Tuner
 
Posts: 21,783
Join Date: Jan 2008
Default 02-07-2013, 09:46 AM

For those adding in the DATA Cable or REV3 Blue Tooth to the new enclosure here are some install directions.
Attached Images
 


Burger Motorsports
Home of the Worlds fastest N20s, N54s, N55s, S55s, N63s, and S63s!

It is the sole responsibility of the purchaser and installer of any BMS part to employ the correct installation techniques required to ensure the proper operation of BMS parts, and BMS disclaims any and all liability for any part failure due to improper installation or use. It is the sole responsibility of the customer to verify that the use of their vehicle and items purchased comply with federal, state and local regulations. BMS claims no legal federal, state or local certification concerning pollution controlled motor vehicles or mandated emissions requirements. BMS products labeled for use only in competition racing vehicles may only be used on competition racing vehicles operated exclusively on a closed course in conjunction with a sanctioned racing event, in accordance with all federal and state laws, and may never be operated on public roads/highways. Please click here for more information on legal requirements related to use of BMS parts.
Reply With Quote
(#3)
Old
Terry @ BMS's Avatar
Terry @ BMS Terry @ BMS is online now
Tuner
 
Posts: 21,783
Join Date: Jan 2008
Default 02-07-2013, 09:47 AM

Quote:
Originally Posted by BavarianBullet
Wow, you didn't waste much time Terry. Good work! Love this and the recent 450WHP on factory turbos.

So when are you going to just cave and drop a dynojet into your home garage?
Heh my neighbors would love that.


Burger Motorsports
Home of the Worlds fastest N20s, N54s, N55s, S55s, N63s, and S63s!

It is the sole responsibility of the purchaser and installer of any BMS part to employ the correct installation techniques required to ensure the proper operation of BMS parts, and BMS disclaims any and all liability for any part failure due to improper installation or use. It is the sole responsibility of the customer to verify that the use of their vehicle and items purchased comply with federal, state and local regulations. BMS claims no legal federal, state or local certification concerning pollution controlled motor vehicles or mandated emissions requirements. BMS products labeled for use only in competition racing vehicles may only be used on competition racing vehicles operated exclusively on a closed course in conjunction with a sanctioned racing event, in accordance with all federal and state laws, and may never be operated on public roads/highways. Please click here for more information on legal requirements related to use of BMS parts.
Reply With Quote
(#4)
Old
stom_m3 stom_m3 is offline
New Member
 
Posts: 2
Join Date: Jan 2013
Car: '13 335i MSport
Default 02-07-2013, 10:32 AM

Quote:
Originally Posted by Terry @ BMS
We made an update for Stage1 modules running a firmware date that ends in //3. So if your firmware ends in that number then email in for the update.
Terry, the Stage 1 is working out great. Lots of power. Thanks!

A couple of questions;
1. If I just got my harness 2/2, would I have the latest fw? What would be the difference in fw?
2. Am I supposed to disconnect the battery when installing or removing the harness?
3. Will the stage 2 offer any power advantages over stage 1 with a stock engine and no **? Or will the stage 2 just offer the functionality of the CAN interface?
4. Is there only 1 catalytic converter on the 335? I thought most cars had 2 these days.

Thanks!

Last edited by stom_m3; 02-07-2013 at 10:33 AM.. Reason: added question #4
Reply With Quote
(#5)
Old
335R1 335R1 is offline
New Member
 
Posts: 16
Join Date: Mar 2010
Car: F30 335i
Default 02-07-2013, 11:07 AM

Now we're talking Terry. I have almost 20k miles on my F30 already and no tune yet. Just waiting for that Stage 2.
Reply With Quote
(#6)
Old
Terry @ BMS's Avatar
Terry @ BMS Terry @ BMS is online now
Tuner
 
Posts: 21,783
Join Date: Jan 2008
Default 02-07-2013, 12:05 PM

Quote:
Originally Posted by stom_m3
Terry, the Stage 1 is working out great. Lots of power. Thanks!

A couple of questions;
1. If I just got my harness 2/2, would I have the latest fw? What would be the difference in fw?
2. Am I supposed to disconnect the battery when installing or removing the harness?
3. Will the stage 2 offer any power advantages over stage 1 with a stock engine and no **? Or will the stage 2 just offer the functionality of the CAN interface?
4. Is there only 1 catalytic converter on the 335? I thought most cars had 2 these days.

Thanks!
1) I don't know. Maybe. Check the firmware date and email it in and we can check.
2) Yes, per the install guide.
3) More power, less lag, better features.
4) Yes. One big one.


Burger Motorsports
Home of the Worlds fastest N20s, N54s, N55s, S55s, N63s, and S63s!

It is the sole responsibility of the purchaser and installer of any BMS part to employ the correct installation techniques required to ensure the proper operation of BMS parts, and BMS disclaims any and all liability for any part failure due to improper installation or use. It is the sole responsibility of the customer to verify that the use of their vehicle and items purchased comply with federal, state and local regulations. BMS claims no legal federal, state or local certification concerning pollution controlled motor vehicles or mandated emissions requirements. BMS products labeled for use only in competition racing vehicles may only be used on competition racing vehicles operated exclusively on a closed course in conjunction with a sanctioned racing event, in accordance with all federal and state laws, and may never be operated on public roads/highways. Please click here for more information on legal requirements related to use of BMS parts.
Reply With Quote
(#7)
Old
NateDog07V NateDog07V is offline
New Member
 
Posts: 1
Join Date: Feb 2013
Car: F30 335i M Sport
Default 02-07-2013, 12:20 PM

Does Map0 on the Stage 2 represent having the tune completely off, or is it like a mini Stage 1 tune which is actually available as Map0 on the Stage 2? either way, thanks for getting the ball rolling on this! Definitely looking fwd to the added power come spring time
Reply With Quote
(#8)
Old
Buildbright Buildbright is offline
New Member
 
Posts: 29
Join Date: Jan 2013
Car: 2013 335i 8AT
Default 02-07-2013, 12:22 PM

Quote:
Originally Posted by Terry @ BMS
1) I don't know. Maybe. Check the firmware date and email it in and we can check.
2) Yes, per the install guide.
3) More power, less lag, better features.
4) Yes. One big one.
I am guessing Stage 2 will have CAN code delete built in and Meth Support will come later?

BTW. You are the F30 Hero!
Reply With Quote
(#9)
Old
stom_m3 stom_m3 is offline
New Member
 
Posts: 2
Join Date: Jan 2013
Car: '13 335i MSport
Default 02-07-2013, 12:25 PM

Quote:
Originally Posted by Terry @ BMS
1) I don't know. Maybe. Check the firmware date and email it in and we can check.
2) Yes, per the install guide.
3) More power, less lag, better features.
4) Yes. One big one.
How do you check the fw date?
Reply With Quote
(#10)
Old
Terry @ BMS's Avatar
Terry @ BMS Terry @ BMS is online now
Tuner
 
Posts: 21,783
Join Date: Jan 2008
Default 02-07-2013, 12:26 PM

Quote:
Originally Posted by Buildbright
I am guessing Stage 2 will have CAN code delete built in and Meth Support will come later?

BTW. You are the F30 Hero!
Correct on both, as well as E85 support.


Burger Motorsports
Home of the Worlds fastest N20s, N54s, N55s, S55s, N63s, and S63s!

It is the sole responsibility of the purchaser and installer of any BMS part to employ the correct installation techniques required to ensure the proper operation of BMS parts, and BMS disclaims any and all liability for any part failure due to improper installation or use. It is the sole responsibility of the customer to verify that the use of their vehicle and items purchased comply with federal, state and local regulations. BMS claims no legal federal, state or local certification concerning pollution controlled motor vehicles or mandated emissions requirements. BMS products labeled for use only in competition racing vehicles may only be used on competition racing vehicles operated exclusively on a closed course in conjunction with a sanctioned racing event, in accordance with all federal and state laws, and may never be operated on public roads/highways. Please click here for more information on legal requirements related to use of BMS parts.
Reply With Quote
(#11)
Old
335R1 335R1 is offline
New Member
 
Posts: 16
Join Date: Mar 2010
Car: F30 335i
Default 02-07-2013, 07:01 PM

The only upgrades I allow on my car has to come directly from Burger Motorsports. I haven't even put aftermarket wheels on. I want them to ask what's underneath that stock F30. I'll tell them BMS. It was like that on my E92 and it'll be like that in the F30.
Reply With Quote
(#12)
Old
135idct 135idct is offline
Junior Member
 
Posts: 291
Join Date: May 2012
Default 02-08-2013, 12:43 AM

Terry do u think the transmission can handle that huge torque, i think with meth
the car will hit 480 rwtq and smash the tranny
Reply With Quote
(#13)
Old
Terry @ BMS's Avatar
Terry @ BMS Terry @ BMS is online now
Tuner
 
Posts: 21,783
Join Date: Jan 2008
Default 02-08-2013, 09:09 AM

No idea. I'll let you know if I run in to problems with it.


Burger Motorsports
Home of the Worlds fastest N20s, N54s, N55s, S55s, N63s, and S63s!

It is the sole responsibility of the purchaser and installer of any BMS part to employ the correct installation techniques required to ensure the proper operation of BMS parts, and BMS disclaims any and all liability for any part failure due to improper installation or use. It is the sole responsibility of the customer to verify that the use of their vehicle and items purchased comply with federal, state and local regulations. BMS claims no legal federal, state or local certification concerning pollution controlled motor vehicles or mandated emissions requirements. BMS products labeled for use only in competition racing vehicles may only be used on competition racing vehicles operated exclusively on a closed course in conjunction with a sanctioned racing event, in accordance with all federal and state laws, and may never be operated on public roads/highways. Please click here for more information on legal requirements related to use of BMS parts.
Reply With Quote
(#14)
Old
v8bait's Avatar
v8bait v8bait is offline
Junior Member
 
Posts: 398
Join Date: Oct 2011
Car: E92 335i 6MT
Default 02-08-2013, 09:45 AM

Holy Torque Batman! I don't like the scaling differences on your Y axis, it kinda hides the massive torque increase you got, but anyway that thing looks ready to roast some tires on map 2! Nice to see the platform moving along.
Reply With Quote
(#15)
Old
justohigh justohigh is offline
Junior Member
 
Posts: 32
Join Date: Aug 2010
Car: 2007 335i coupe
Default 02-08-2013, 11:19 AM

Wow, that is a lot of torque. What's the explanation for that? It beats the E9x n54 and n55 in torque when going mod for mod.
Reply With Quote
(#16)
Old
Terry @ BMS's Avatar
Terry @ BMS Terry @ BMS is online now
Tuner
 
Posts: 21,783
Join Date: Jan 2008
Default 02-08-2013, 11:35 AM

The peak torque numbers are a bit of a spike at the start of the run. It's on par with any other N55 in terms of torque production per mod.


Burger Motorsports
Home of the Worlds fastest N20s, N54s, N55s, S55s, N63s, and S63s!

It is the sole responsibility of the purchaser and installer of any BMS part to employ the correct installation techniques required to ensure the proper operation of BMS parts, and BMS disclaims any and all liability for any part failure due to improper installation or use. It is the sole responsibility of the customer to verify that the use of their vehicle and items purchased comply with federal, state and local regulations. BMS claims no legal federal, state or local certification concerning pollution controlled motor vehicles or mandated emissions requirements. BMS products labeled for use only in competition racing vehicles may only be used on competition racing vehicles operated exclusively on a closed course in conjunction with a sanctioned racing event, in accordance with all federal and state laws, and may never be operated on public roads/highways. Please click here for more information on legal requirements related to use of BMS parts.
Reply With Quote
(#17)
Old
J-boogey J-boogey is offline
New Member
 
Posts: 9
Join Date: Aug 2010
Car: 2010 E92 335 xdrive M-Sport
Default 02-08-2013, 06:27 PM

Quote:
Originally Posted by Terry @ BMS
We made an update for Stage1 modules running a firmware date that ends in //3. So if your firmware ends in that number then email in for the update.
terry, how do you find out what firmware date you have? I got the tune in January
Reply With Quote
(#18)
Old
Terry @ BMS's Avatar
Terry @ BMS Terry @ BMS is online now
Tuner
 
Posts: 21,783
Join Date: Jan 2008
Default 02-08-2013, 06:33 PM

It's under the user adjustment tab.


Burger Motorsports
Home of the Worlds fastest N20s, N54s, N55s, S55s, N63s, and S63s!

It is the sole responsibility of the purchaser and installer of any BMS part to employ the correct installation techniques required to ensure the proper operation of BMS parts, and BMS disclaims any and all liability for any part failure due to improper installation or use. It is the sole responsibility of the customer to verify that the use of their vehicle and items purchased comply with federal, state and local regulations. BMS claims no legal federal, state or local certification concerning pollution controlled motor vehicles or mandated emissions requirements. BMS products labeled for use only in competition racing vehicles may only be used on competition racing vehicles operated exclusively on a closed course in conjunction with a sanctioned racing event, in accordance with all federal and state laws, and may never be operated on public roads/highways. Please click here for more information on legal requirements related to use of BMS parts.
Reply With Quote
(#19)
Old
pnosker pnosker is offline
Junior Member
 
Posts: 33
Join Date: Jun 2011
Default 02-09-2013, 11:38 PM

Happy to test if you need someone!
Reply With Quote
(#20)
Old
ridin135 ridin135 is offline
New Member
 
Posts: 25
Join Date: Apr 2009
Default 02-10-2013, 09:31 AM

Terry by chance will you be releasing a meth kit for the f30?
Reply With Quote
(#21)
Old
Terry @ BMS's Avatar
Terry @ BMS Terry @ BMS is online now
Tuner
 
Posts: 21,783
Join Date: Jan 2008
Default 02-10-2013, 10:17 AM

Quote:
Originally Posted by ridin135
Terry by chance will you be releasing a meth kit for the f30?
We will some day.


Burger Motorsports
Home of the Worlds fastest N20s, N54s, N55s, S55s, N63s, and S63s!

It is the sole responsibility of the purchaser and installer of any BMS part to employ the correct installation techniques required to ensure the proper operation of BMS parts, and BMS disclaims any and all liability for any part failure due to improper installation or use. It is the sole responsibility of the customer to verify that the use of their vehicle and items purchased comply with federal, state and local regulations. BMS claims no legal federal, state or local certification concerning pollution controlled motor vehicles or mandated emissions requirements. BMS products labeled for use only in competition racing vehicles may only be used on competition racing vehicles operated exclusively on a closed course in conjunction with a sanctioned racing event, in accordance with all federal and state laws, and may never be operated on public roads/highways. Please click here for more information on legal requirements related to use of BMS parts.
Reply With Quote
(#22)
Old
Terry @ BMS's Avatar
Terry @ BMS Terry @ BMS is online now
Tuner
 
Posts: 21,783
Join Date: Jan 2008
Default 02-12-2013, 11:37 AM

Here is a video of how the map switching will work on the F30 JB4 until we're able to get full dash control.



Burger Motorsports
Home of the Worlds fastest N20s, N54s, N55s, S55s, N63s, and S63s!

It is the sole responsibility of the purchaser and installer of any BMS part to employ the correct installation techniques required to ensure the proper operation of BMS parts, and BMS disclaims any and all liability for any part failure due to improper installation or use. It is the sole responsibility of the customer to verify that the use of their vehicle and items purchased comply with federal, state and local regulations. BMS claims no legal federal, state or local certification concerning pollution controlled motor vehicles or mandated emissions requirements. BMS products labeled for use only in competition racing vehicles may only be used on competition racing vehicles operated exclusively on a closed course in conjunction with a sanctioned racing event, in accordance with all federal and state laws, and may never be operated on public roads/highways. Please click here for more information on legal requirements related to use of BMS parts.
Reply With Quote
(#23)
Old
NICKTENN's Avatar
NICKTENN NICKTENN is offline
New Member
 
Posts: 24
Join Date: Apr 2012
Car: F30 335i Sportline on order
Default 02-12-2013, 03:47 PM

Any hints on where the CAN connection is made?


2016 F30 340i M Sport Alpine White, JB4

RIP 2012 F30 335i Sport Line Mineral Gray, JB3/Stage 1

Stock 335i 1/4 mile time
Reply With Quote
(#24)
Old
BMW335N55's Avatar
BMW335N55 BMW335N55 is offline
New Member
 
Posts: 3
Join Date: Feb 2013
Car: BMW F30 335i
Default 02-12-2013, 08:26 PM

Awsome Terry thank you for keeping up on the F10 F30 upgrades, cant wait to have full dash control
Reply With Quote
(#25)
Old
spideypm spideypm is offline
New Member
 
Posts: 13
Join Date: Feb 2013
Car: 2013 F30 335i M Sport
Default 02-15-2013, 01:09 PM

Hi Terry, any ETA for this?
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 3 (0 members and 3 guests)
 
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump




vBulletin Skin developed by: vBStyles.com
Copyright 2007 - 2017, N54tech.com